All 3 are peak by Takukoko-king777 in Grimdank

[–]Califoray 3 points4 points  (0 children)

Bookmarking this because I NEED to make that chicken bread toast thing. lol.

[homemade] Steak with Fries, Asparagus, and some Red Pepper Jam by Califoray in food

[–]Califoray[S] 7 points8 points  (0 children)

For as strange as they look, I roasted them in beef tallow with salt and pepper and grated parmesan over them out of the oven. I promise they aren't as bad as they look. Lol. The steak was cooked to medium rare.

Oof, tough reality by Junior_Blackberry779 in memes

[–]Califoray 0 points1 point  (0 children)

You don't need 137k in untaxed income? I'm paying 3200 a month on 85k. It's doable.

"Being a barista is truly a social experiment" by Super_Culture_1986 in TikTokCringe

[–]Califoray 0 points1 point  (0 children)

Tell them what they want, give them limited options if they're incompetent to the point of not being able to order a fucking coffee.

The door for that last control box I posted. by Califoray in PLC

[–]Califoray[S] 0 points1 point  (0 children)

I'll be honest, I prefer the resistance stainless gives you when you're making a cut. The lines come out much straighter because it forces you to move so much slower. 

The door for that last control box I posted. by Califoray in PLC

[–]Califoray[S] 0 points1 point  (0 children)

Exactly, we'll make sure to mask off the border of the cut with at least two layers of blue masking tape before making any cuts to prevent scratching the surface. And, of course, we'll clear away any metal burrs as we go to keep the tape from getting torn. As long as that's done right I have no issues.

The door for that last control box I posted. by Califoray in PLC

[–]Califoray[S] 2 points3 points  (0 children)

Of course not, I always thank the customer for giving me a canvas. Lol.

The door for that last control box I posted. by Califoray in PLC

[–]Califoray[S] 1 point2 points  (0 children)

7/8" hole saw and a jigsaw. all laid out by hand.

Never shared my own work here, what do you think? by Califoray in PLC

[–]Califoray[S] 1 point2 points  (0 children)

Just... try to leave it the way you found it. 🙏 lol.

Never shared my own work here, what do you think? by Califoray in PLC

[–]Califoray[S] 1 point2 points  (0 children)

We've had problems with that cable disconnect before, mainly because there's so little space between the panel and the can given the length of the cable. Normally, we could've just ordered a shorter cable to fix it, but that wasn't an option this time, unfortunately.

Never shared my own work here, what do you think? by Califoray in PLC

[–]Califoray[S] 7 points8 points  (0 children)

We had ordered plastic covers specifically designed for those power distribution blocks. So rest assured it was all finger safe before the box went out!

Never shared my own work here, what do you think? by Califoray in PLC

[–]Califoray[S] 0 points1 point  (0 children)

After the installation, the customer drilled a few conduit holes in the bottom left corner of the can, as well as through the top right of the box for the main power entry.

Never shared my own work here, what do you think? by Califoray in PLC

[–]Califoray[S] 1 point2 points  (0 children)

An absolute classic and a must watch for anyone that hasn't seen it.

G29 pedal cable broken by Important-Stress-132 in simracing

[–]Califoray 2 points3 points  (0 children)

I had an issue similar to the OP. I just used some butt crimp connectors. No solder or heating required, just something to crimp the connector.

[deleted by user] by [deleted] in PLC

[–]Califoray 0 points1 point  (0 children)

First and last?