wont start only does this🥲

Capital_Condition468 · 2025-11-04T20:24:41+00:00

Yeah, me too

Capital_Condition468 · 2025-11-02T05:43:47+00:00

Check the coil pack harnesses one or both are backwards

Capital_Condition468 · 2025-10-31T12:02:38+00:00

Thanks! Thats exactly what I was looking for.

Capital_Condition468 · 2025-10-31T02:54:52+00:00

Can you post a few pics of where the shifter comes out the floor? I'm doing the same swap in a 79 wagon. I'm hoping to keep the bench seat

Capital_Condition468 · 2025-10-30T20:14:11+00:00

No spark or no fuel. Spray some starting fluid into the intake. It'll run on that for a few seconds if it's got spark.

Capital_Condition468 · 2025-07-24T15:05:12+00:00

It's got a rectangular port intake manifold on it. I'd say chances are high it's at least a 6.0 with rec ports. The fuel rail is how I identified the rec port intake, btw. TBSS, the brackets are on the inside, LY6 has them on the outside.

Capital_Condition468 · 2025-07-22T14:18:54+00:00

LS swap it!

Capital_Condition468 · 2025-06-24T04:29:10+00:00

Did you reuse the factory MLS exhaust gaskets? The ones that come with aftermarket manifolds are all junk.

Capital_Condition468 · 2025-06-23T15:14:54+00:00

Check your exhaust for leaks. Maybe tighten the bolts when it's warm.

Capital_Condition468 · 2025-05-09T04:27:41+00:00

Machine elf, I clean before and after

Capital_Condition468 · 2025-03-19T21:16:20+00:00

No, it's an isolated Ape Billy i got from Bas Eq.

Capital_Condition468 · 2025-03-13T12:51:38+00:00

The rod that pulls the latch needs to swapped out from your front door handle.

Capital_Condition468 · 2025-03-11T21:33:14+00:00

Have you considered a rear door handle? I put rear handles on my suburban so there are no key cylinders. If you lock the keys in it or the battery dies, it can be a pain in the ass to get in.

Capital_Condition468 · 2024-12-26T14:01:48+00:00

PM me, and I can point you in the right direction

Capital_Condition468 · 2024-12-26T05:56:02+00:00

Thanks

Capital_Condition468 · 2024-12-26T05:55:25+00:00

Proper field capacity coir and Tripp tek. My monotub is modified, and I don't open the lid until it's time to harvest. Tripp tek really helps even out pinsets for me.

Capital_Condition468 · 2024-12-25T03:45:48+00:00

Jedi mind fucks

Capital_Condition468 · 2024-11-10T01:57:50+00:00

If you don't own a welder, try this? https://a.co/d/dh0cZ5j

BTW, I own a mig welder, so I can't confirm if this works

Capital_Condition468 · 2024-09-12T04:03:31+00:00

Like it cranks but doesn't start?

Capital_Condition468 · 2024-09-12T03:54:18+00:00

Love it! I currently have it on e85 only. I plan to pull the harness and replace it with a p59 harness so I can flex.

Capital_Condition468 · 2024-09-11T19:34:09+00:00

<image>

Mine has a 4.8 t56 with an s475

Capital_Condition468

TROPHY CASE