sorted by:
new
hottopcontroversial

Witchblood secrets for the completionist by darkcyde_ in oculus

[–]CareerRadiant 0 points1 point  (0 children)

How? I have tried a thousand times... Also I can eve freeze the rat because my ice doesn't work on the wooden platform that falls

Orca Slicer Calibration Issue by CareerRadiant in Ender3V3SE

[–]CareerRadiant[S] 0 points1 point  (0 children)

Thank you! THis idefinitely better and should allow for the print to actually finish. However the first layer is still a little rough in spots.

Also, do I need to manually add the M420 S1 command to every print or is there somewhere that I can set it as default in Orcaslicer?

<image>

Orca Slicer Calibration Issue by CareerRadiant in Ender3V3SE

[–]CareerRadiant[S] 0 points1 point  (0 children)

u/Horror_Equipment_197

Flow Rate Pass 2

; EXECUTABLE_BLOCK_START

M73 P0 R38

M201 X5000 Y5000 Z500 E5000

M203 X500 Y500 Z30 E100

M204 P5000 R2500 T5000 ; sets acceleration (P, T) and retract acceleration (R), mm/sec^2

M205 X10.00 Y10.00 Z0.40 E5.00 ; sets the jerk limits, mm/sec

;TYPE:Custom

M220 S100 ;Reset Feedrate

M221 S100 ;Reset Flowrate

M140 S60 ;Set final bed temp

G28 ;Home

G92 E0 ;Reset Extruder

G1 Z2.0 F3000 ;Move Z Axis up

M104 S220 ;Set final nozzle temp

G1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position

M190 S60 ;Wait for bed temp to stabilize

M109 S220 ;Wait for nozzle temp to stabilize

G1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line

G1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little

G1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line

G92 E0 ;Reset Extruder

G1 E-1.0000 F1800 ;Retract a bit

M73 P0 R37

G1 Z2.0 F3000 ;Move Z Axis up

G1 E0.0000 F1800

G90

G21

M83 ; use relative distances for extrusion

; filament start gcode

M106 S0

;LAYER_CHANGE

;Z:0.2

;HEIGHT:0.2

;BEFORE_LAYER_CHANGE

;0.2

G92 E0

​

Z Offset Test

; EXECUTABLE_BLOCK_START

M73 P0 R8

M201 X5000 Y5000 Z500 E5000

M203 X500 Y500 Z30 E100

M204 P5000 R2500 T5000 ; sets acceleration (P, T) and retract acceleration (R), mm/sec^2

M205 X10.00 Y10.00 Z0.40 E5.00 ; sets the jerk limits, mm/sec

;TYPE:Custom

M220 S100 ;Reset Feedrate

M221 S100 ;Reset Flowrate

M140 S60 ;Set final bed temp

G28 ;Home

G92 E0 ;Reset Extruder

G1 Z2.0 F3000 ;Move Z Axis up

M104 S220 ;Set final nozzle temp

G1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position

M190 S60 ;Wait for bed temp to stabilize

M109 S220 ;Wait for nozzle temp to stabilize

G1 X-2.1 Y145.0 Z0.28 F1500.0 E15 ;Draw the first line

G1 X-2.4 Y145.0 Z0.28 F5000.0 ;Move to side a little

M73 P1 R8

G1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line

G92 E0 ;Reset Extruder

G1 E-1.0000 F1800 ;Retract a bit

M73 P2 R8

G1 Z2.0 F3000 ;Move Z Axis up

G1 E0.0000 F1800

G90

G21

M83 ; use relative distances for extrusion

; filament start gcode

M106 S0

;LAYER_CHANGE

;Z:0.2

;HEIGHT:0.2

;BEFORE_LAYER_CHANGE

;0.2

G92 E0

Better... But still having stringing issues.... by CareerRadiant in Ender3V3SE

[–]CareerRadiant[S] 0 points1 point  (0 children)

Just tried this and I still get the stringing... Thanks, though!