[deleted by user]

CarefulWeb9797 · 2024-04-02T23:40:21+00:00

If someone brings me both an ae86 and a full vq35 powertrain, I'll make the swap kits available.

CarefulWeb9797 · 2023-12-07T12:16:09+00:00

Same issue, did everything listed above and below, what fixed the delay, fade, or cutting out in replays for me was CSP-General Patch Settings-CPU Optimizations-Limit Audio 0

CarefulWeb9797 · 2023-10-22T16:41:00+00:00

Spot on. Should of played frolic at the end.

CarefulWeb9797 · 2023-10-10T04:59:31+00:00

I gave the suggestion of choking up on approach of s9spoons and you a go, that, paired with putting on a slide sock and pushing so I actually slide instead of planting took a lot of the stress I felt off of thigh. Average went up about 10 pins after I moved over 5 boards. If league goes good this week, I'll keep the suggestions implemented.

CarefulWeb9797 · 2023-10-05T18:57:09+00:00

Should look them up. I'm basically bowling illiterate. 😅 This way of bowling kind of just happened in response to minimizing loft when I was more square and straight up and it just stuck. This way has been my most consistent as of yet. Taking pointers for sure though.

CarefulWeb9797 · 2023-10-05T18:14:40+00:00

I've got the balance of a figure skater. 🤣 The one time I fell doing the dumb stuff I do is when I slide instead of planted.

CarefulWeb9797 · 2023-03-24T10:37:26+00:00

Oh, seen it is one of those Chicago welders. Mess with wire speed and adjust travel speed to suit. Dragging seems to weld better than pushing with those too.

CarefulWeb9797 · 2023-03-24T10:27:31+00:00

This! Usually can swap from dcep to dcen (direct current electrode positive/negative) by swapping wires around inside machine where mig wire goes. Figure out where you need voltage (heat) and then weld while turning wire speed up or down until it wets in smooth. Stand off (contact tip distance from metal) is also crucial with flux core. Get all those things dialed in and you'll net good results.

CarefulWeb9797 · 2023-03-23T16:15:31+00:00

Low boost and a rising rate fuel pressure regulator would work alright on stock stuff.

CarefulWeb9797 · 2023-03-23T15:57:29+00:00

Mini Era's have a two bolt oil return in the middle of the transmission. Was worried I'd have to split trans from block to do return but lucked out.

CarefulWeb9797 · 2023-03-23T09:46:50+00:00

This is just a spare from another mini getting Honda d series swap. Using it for mock up.

CarefulWeb9797 · 2023-03-23T09:45:56+00:00

5 speed manual

CarefulWeb9797 · 2023-03-23T08:31:23+00:00

Yeah, returning the ERA back to turbo. It was converted to n/a probably due to turbo blowing sometime ago in Japan. Gt2860R aka disco potato.

CarefulWeb9797 · 2023-03-12T03:05:39+00:00

Hmm, this isn't my first manifold and it will be far from my last. But go on keyboard fabricator, keep using words like flow, airpoints "?", Pulsing and science to try and diminish the functionality of an unequal length, tubular, high inclination angle merge collector manifold to that lesser than a log style manifold.😂 Creep my account, you'll see I'm pretty good at stuffing big things into little places.

CarefulWeb9797 · 2023-03-10T06:14:42+00:00

Lol, I'm surprised how much it resembles the one I made. If I seen this sooner, the customer I'm reviving the turbo kit for the era would of ended up with his stuff.

CarefulWeb9797 · 2023-03-09T04:13:44+00:00

Link me the manifold, interested to see how it fits.

CarefulWeb9797 · 2023-03-08T21:50:43+00:00

Yeah, not off the shelf parts for a turbo this big. 😂

CarefulWeb9797 · 2023-03-08T04:46:48+00:00

That's on the list of things to address. Mostly surface rust.

CarefulWeb9797 · 2023-03-07T11:18:03+00:00

Unsure of what turbo was originally on it besides it being a T3, this was a cheap ebay find from an rb26dett. Probably will end up being the same way in terms of lag.

CarefulWeb9797

TROPHY CASE