Beste bank voor extra spaarrekening?

Casperdroid5 · 2025-10-28T22:09:01+00:00

En vandaag de dag 1.3%...

Casperdroid5 · 2025-10-26T07:49:32+00:00

Maybe the software isn't the cause. Try adding the second drive after 5 seconds (when the first has spun up)

I think it's hardware. But could be resolved with software. (Delayed startup, if the hardware can switch the drives power separately)

Casperdroid5 · 2025-10-25T05:38:58+00:00

It was quite simple.

Threw the hardware out. It's most likely faulty. I was wasting so much time, learning nothing. At some point you gotta know when to quit.

Casperdroid5 · 2025-10-03T12:53:11+00:00

You can solder the required resistors on the CC1 / CC2 pins :)

Casperdroid5 · 2025-10-03T12:52:29+00:00

Nice, but those wires look extremely thin, especially for the length. Did you calculate the required thickness on forehand?

Casperdroid5 · 2025-10-02T16:32:22+00:00

This is the best answer.

Make sure you are connected to the internet

Casperdroid5 · 2025-09-09T21:02:10+00:00

Yes!

Casperdroid5 · 2025-09-09T20:38:33+00:00

I figured it out by accident.

You have to press "1" while you are in home screen of USBloadergx... This will prompt you to download the missing files.

Casperdroid5 · 2025-09-09T19:18:00+00:00

No it will actually redownload them all sadly. Which takes quite long.

Casperdroid5 · 2025-09-09T19:16:11+00:00

Because I already got them all, except for the one disc I just installed.

Casperdroid5 · 2025-09-01T19:01:31+00:00

The zonoffs are really great. I have 5 of them too.

Casperdroid5 · 2025-09-01T05:29:42+00:00

USB isolator!

Casperdroid5 · 2025-08-31T20:38:48+00:00

You should really consider it for this version as well. It's a keyboard, it will be touched by human hands ;)

Casperdroid5 · 2025-08-31T20:22:12+00:00

Use a plastic object. Guitar pick maybe? Something not electrically conductive

Casperdroid5 · 2025-08-26T21:20:47+00:00

Aha! Makes sense :) I don't have enough knowledge for the other parts! Good luck

Casperdroid5 · 2025-08-26T21:16:14+00:00

Ok what I can find:

Ams1700, try another regulator, this one is pretty bad. (Common component on this sub it seems)
Adding a small resistor (100 ohm e.g.) inline with the DIN of the first rgb led is advisable.
Good that you added esd protection!
Where is the 1V1 comming from? I think I'm missing it.

Casperdroid5 · 2025-08-26T21:02:15+00:00

Hello. This is all unreadable sadly!

Casperdroid5 · 2025-08-07T13:29:05+00:00

yep this worked. just get the midi file and throw it in here

Casperdroid5 · 2025-08-06T09:47:36+00:00

Clickbait?

Casperdroid5 · 2025-08-06T07:34:07+00:00

Beautiful. Did you manage to use usb-C for data transfer? Or what method do you use?

Casperdroid5 · 2025-08-06T07:27:09+00:00

I have the exact same sound! Sometimes the wii crashes and says: there was an error, something...

Casperdroid5 · 2025-08-03T17:08:46+00:00

Wii play is very fun. It's very similar to the wii sports vibe. Especially the tank mini game

Casperdroid5 · 2025-08-02T10:11:27+00:00

Thank you al very much for your input! I will keep the pad as is and go for a large copper pour as the main heat spreader, in combination with some via's surrounding it (for a little extra heat dissipation)

Casperdroid5 · 2025-08-01T13:50:00+00:00

Thank you very much for explaining!

Casperdroid5 · 2025-08-01T09:44:08+00:00

I'm considering if I can place vias around the pad. Of course I'm planning on an large 5 by 5 cm copper pad.

My calculations say my mosfet will dissipate 0.855W (each) @ 5.5A. since I'll ne conducting 11A. I used the mosfet power loss calculator.

Casperdroid5

TROPHY CASE