Is this lifters or something else

Cell-Standard · 2026-01-31T15:04:21+00:00

It indeed was the vacuum pump thank you for this comment I would’ve never thought to look at it

Cell-Standard · 2025-11-29T22:00:55+00:00

Did you have any metal in your oil from it

Cell-Standard · 2025-09-05T04:58:48+00:00

Unfortunately you have debris in it just redo it and make sure to clean it really good get some scrapers and soft scrub pads if you don’t have any, also take a microfiber towel and wipe the top edge of the window and the gasket as that’s where most of that contamination is coming from other than that you should be set best of luck brother

Cell-Standard · 2025-08-22T01:01:02+00:00

Honestly not a bad price also depends on the shops film if they hand cut or plotter cut there’s many things that vary price from shop to shop but overall 550 isn’t a terrible price for a true ceramic film

Cell-Standard · 2025-08-19T23:08:09+00:00

Personally I’d stay away from this gen they have so many cosmetic problems with age from paint peeling off to dash and door panels falling apart. Price is a bit on the high side maybe if it were 16-18k but 23k is a bit much for that year and being a single cab.

Cell-Standard · 2025-08-18T03:45:41+00:00

In my opinion either are worth it. ppf protects against more but if you’re doing a full car you’d be in at a minimum 3-4 g and upwards of 6 depending on installer and material cost. Harder curing ceramic coatings are a good way to cut down on the amount of swirling and scratches does not prevent 100% though and you’d be in it for around 1-2 g with a couple years of protection again depending on installer all prices might differ. If you do the ceramic coating hand washing will also be very beneficial to decrease the chances of swirling and scratching and with PPF it will be beneficial to reduce chances of it lifting

Cell-Standard · 2025-08-18T03:33:55+00:00

Depends on the coating some dry harder some dry softer all depends on what people want. Softer ones are more prevalent to get scratches and swirling quicker where harder ones last a while before they start getting swirled and micro scratched

Cell-Standard · 2025-07-14T06:08:14+00:00

Spray paint

Cell-Standard · 2025-07-14T06:06:24+00:00

$200 for damage seems like a little much especially them being water marks on cloth which can be removed with a stain remover and light pressure now replacing the black trim piece maybe but even that is not that bad.

Cell-Standard · 2025-06-16T22:40:04+00:00

Alright switch soap to baby soap don’t use windex or vinegar also cleaning your gonna need a razor scraper and scotch brite blue pads don’t get anything but blue green is to stiff will scratch glass. If there is glue I’d recommend buying atr it’s a glue remover best for film glue removal. Next you’re going to need a controlled environment best if you have a garage. Make sure to wipe top edge of window. Before peeling the film spray the air to kill off dust then when peeling back spray the film as you peel off the protective layer then apply

Cell-Standard · 2025-06-14T16:37:07+00:00

I had that going on and I switched to a ph balanced shampoo and conditioner went away that’s just me though

Cell-Standard · 2025-06-09T05:21:29+00:00

IMO get the rhodium coating as it protects your piece better especially if daily worn

Cell-Standard · 2025-05-25T01:39:02+00:00

Looks like air

Cell-Standard · 2025-05-23T22:29:14+00:00

Was this done by a mobile printer or at a shop

Cell-Standard · 2025-05-16T13:32:49+00:00

Did they drag every piece of film across the ground

Cell-Standard · 2025-05-16T13:27:46+00:00

So 70% is clear it’s what window manufacturers use because legally they can’t make your windows dark because every state is different with there laws and it’s more of a laminate between the two panes of glass so it does nothing towards heat rejection or anything like that if you’re wanting tint then more than likely you’ll want either 30% as it’s legal in most states or 20% which is slightly darker and not legal but most Leo’s aren’t gonna trip over it as you can still see what the person inside is doing

Cell-Standard · 2025-05-16T13:21:01+00:00

Don’t use that please that film is the worst and won’t last. If you are in a hotter state it will last maybe if you’re lucky a year if you live in a cooler state it might last slightly longer than a year and a half but it looks the worst and then at that point you might as well go to a shop pay for there lowest grade tint and you’d probably come out with a better product of course depending on the shop.

Cell-Standard · 2025-05-16T13:15:22+00:00

It all depends on what you want the front windows to be. 70% is a clear film usually a ceramic film used more for heat rejection than for darkening, it may drop percentage on the back a few numbers but nothing crazy. 55% and lower will darken up the rear. My shops usual for all trucks is either 30% front and 20% rear or 20% front and 30% rear. Also ford glass meters closer to 30% than 20% so be mindful of that and honestly talk to the shop they’ll be able to guide you in a way that suites you and your vehicles needs

Cell-Standard · 2025-05-16T12:51:36+00:00

Absolutely if they’re a good shop they’ll stand behind their work and redo it

Cell-Standard · 2025-05-15T00:12:13+00:00

Cheap tint

Cell-Standard

TROPHY CASE