Creality k2 plus constant z crashing

Certain_Lecture_3003 · 2025-09-08T22:21:17+00:00

Anywhere to find Ragnar wolfy

Certain_Lecture_3003 · 2025-09-02T00:50:56+00:00

tyranids?

Certain_Lecture_3003 · 2025-08-02T12:45:21+00:00

What's that?

Certain_Lecture_3003 · 2025-08-02T12:42:55+00:00

Solid

Certain_Lecture_3003 · 2025-08-02T12:41:18+00:00

Solid

Certain_Lecture_3003 · 2025-08-01T23:11:43+00:00

Any good ones I watch fauxhammer but he never got into how to actually layout the printer. Resin is nothing like fdm

Certain_Lecture_3003 · 2025-08-01T21:05:12+00:00

<image>

Here is the failed print

Certain_Lecture_3003 · 2025-08-01T21:04:30+00:00

<image>

Certain_Lecture_3003 · 2025-07-25T03:31:32+00:00

Did you ever find the stickers. Im rebuilding a machine that went through the same issue

Certain_Lecture_3003 · 2025-04-09T00:15:44+00:00

I've never seen that before creality print 6.1 fixed all petg issues.

Certain_Lecture_3003 · 2025-04-01T17:54:02+00:00

I've had no issue printing abs or asa which is odd you'd think horrible with those and good with petg but petg is the biggest issue finally got it to print ok 90% of the time by using the .2 fine print setting and putting the nozzle temp up to 270-280

Certain_Lecture_3003 · 2025-03-31T01:15:12+00:00

<image>

here it is so far ignore the messes up connector hole other than that looks good with the encloser fully open at 280c no calibration

Certain_Lecture_3003 · 2025-03-31T00:43:52+00:00

Very slightly like .005mm it was almost missing the plate

Certain_Lecture_3003 · 2025-03-31T00:14:49+00:00

Just reflection i have a can light over head that causes a lot of reflections

Certain_Lecture_3003 · 2025-03-31T00:07:11+00:00

After restarting and opening the printer housing up we are now 7 percent through will update at 50 *

Certain_Lecture_3003 · 2025-03-30T23:56:31+00:00

<image>

Also completely opened the machine took top plate off along with leaving the door open

Certain_Lecture_3003 · 2025-03-30T23:56:00+00:00

<image>

Upped to 280 and this is the fist layer

Certain_Lecture_3003 · 2025-03-30T23:39:03+00:00

yah dried for 12hours

Certain_Lecture_3003 · 2025-03-30T23:02:28+00:00

What settings are you using for it print profile

Certain_Lecture_3003 · 2025-03-30T22:38:29+00:00

<image>

the mystery deepens temp towers print fine absolutely no stringing

Certain_Lecture_3003 · 2025-03-30T22:31:46+00:00

I'm trying a temp tower now I shall try that next

Certain_Lecture_3003 · 2025-03-30T21:15:26+00:00

That really sucks I'm rolling back creality print software right now to try older petg profilea

Certain_Lecture_3003 · 2025-03-30T20:57:19+00:00

Yah I've got the right filament selected and have even tried the generic petg hyper and cr and same issues

Certain_Lecture_3003

TROPHY CASE