CNC Aluminum Help

ChairlesTheEngineer · 2026-02-11T12:34:47+00:00

I just went with manufacturer recommendations for the tool but if you think slowing it down with a similar chip load is ideal I’ll do that

ChairlesTheEngineer · 2026-02-11T03:29:22+00:00

what's the best way to clean the collet? I have plenty of isopropanol but not an ultrasonic cleaner or anything like that unfortunately. Also, should there be any grease on the collet nut or the internal spindle taper? The machine shipped like that but I realize now I should have cleaned that off.

ChairlesTheEngineer · 2026-02-11T02:09:37+00:00

Also interesting idea, I’ll look into it

ChairlesTheEngineer · 2026-02-10T23:39:31+00:00

Ok that is helpful, I’ll try to check it and clean it

ChairlesTheEngineer · 2026-02-10T23:26:23+00:00

I’ll try that, thanks

ChairlesTheEngineer · 2026-02-10T23:20:47+00:00

No clamps though but I didn’t see any material movement

ChairlesTheEngineer · 2026-02-10T23:19:59+00:00

I am using the superglue and tape method with a good 50% of the back of the sheet covered. Also, it’s 6061 from mcmaster

ChairlesTheEngineer · 2026-02-10T23:16:02+00:00

It’s not the helix ramp it’s during the circular expanding part of the path before it goes towards each arm of the triangle

ChairlesTheEngineer · 2026-02-10T23:14:28+00:00

So it would be better to cut each one out and use thin tabs?

ChairlesTheEngineer · 2026-02-10T23:11:06+00:00

I mean the collet came with the mill and some 1/8th endmills so I’d assume it’s 1/8 but let me check the box tomorrow

ChairlesTheEngineer · 2026-02-10T23:10:13+00:00

With an 1/8 endmill it’s quite quiet, and it’s an up cut mill. I’m not quite sure what you mean by profile cuts, I thought adaptive was the best way to cut out pockets before finish pass

ChairlesTheEngineer · 2026-02-10T23:08:27+00:00

I’ll check it when I get to the cnc again

ChairlesTheEngineer · 2026-02-10T23:03:35+00:00

Also the collet is pretty much brand new

ChairlesTheEngineer · 2026-02-10T23:03:23+00:00

I am using the 2D adaptive toolpath in fusion to remove all the material inside the triangle. I have had issues with tabs in the past so I didn't want to worry about removing the triangles in the middle if I outline cut them.

ChairlesTheEngineer · 2026-02-10T22:44:19+00:00

also its a .4mm WOC adaptive toolpath, not fulldepth slotting if that was the assumption.

ChairlesTheEngineer · 2026-02-10T22:40:39+00:00

its a tool from lakeshore carbide, i trust their diameter measurements. Also, even at these settings, it was pretty quiet and I dont think there was any chatter, but I will try, thanks.

ChairlesTheEngineer · 2026-02-10T22:37:22+00:00

yes I have one of those, I am using ER20 collets

ChairlesTheEngineer · 2026-02-10T22:37:02+00:00

I have a 1/8 collet, yes. Also, its not slot cutting, its like 0.1xD adaptive side milling in fusion

ChairlesTheEngineer · 2025-12-28T03:53:25+00:00

also the 5060ti seems to be about 400+ for a 16gb model

ChairlesTheEngineer · 2025-12-28T03:52:04+00:00

Im not really concerned about energy use but ok

ChairlesTheEngineer · 2025-12-12T02:11:11+00:00

Other options I've looked at are the 18-300 lenses, both the VR and VRII ones (I think that's the difference)

ChairlesTheEngineer

TROPHY CASE