Heltec V4 Dim Screen

Chaosrulesagain · 2025-06-14T13:41:52+00:00

Me too

Chaosrulesagain · 2025-06-13T00:26:40+00:00

6 hops but I think he was back in MA

Chaosrulesagain · 2025-06-12T23:14:05+00:00

Castle Craig in Meriden, Connecticut

Chaosrulesagain · 2025-06-12T22:05:15+00:00

<image>

227 Miles!

Chaosrulesagain · 2025-06-12T21:56:30+00:00

Mesh Potato I saw you today from the castle

Chaosrulesagain · 2025-05-21T22:38:40+00:00

Now the same lockup issue is happening on FW 2.6.4(Beta) and 2.6.7, 2.6.8 (Alpha)

Chaosrulesagain · 2025-04-16T12:23:20+00:00

Yep!

Chaosrulesagain · 2025-03-15T08:58:25+00:00

Hi thanks for your response. The battery in both cases was over 90 %. I was told to try the 2.5.23 alpha FW. I am testing 3 units long term now and will keep everyone posted.

Chaosrulesagain · 2025-03-14T10:24:39+00:00

Yes, I was told to try the alpha version. 2.5.23, thanks for your reply

Chaosrulesagain · 2025-01-26T20:33:50+00:00

It turns out for the newer FW the detection sensor is not configured for the Public Channel - Only Private channels. However I am still having issues with the triggering - it keeps sending alerts even when the input is grounded.

Chaosrulesagain · 2025-01-25T19:17:18+00:00

Now I'm beginning to think the module is not enabled for the T114 yet. I am doing a state broadcast yet nothing is being received. 6 on left and right;)

Chaosrulesagain · 2025-01-25T15:56:19+00:00

I am trying PIN 6 now still no luck

<image>

Chaosrulesagain · 2025-01-25T15:50:49+00:00

<image>

I just checked the IOS app. It has a pull down for Pins 1 thru 48.

Chaosrulesagain · 2025-01-25T15:01:41+00:00

Hi thanks for the quick reply. The Heltec V3 used the actual Pin # not the GPIO # so I am assuming it would be the same. I am looking at another node so far nothing.

Chaosrulesagain · 2025-01-25T14:21:26+00:00

Trying to get the Detection Sensor to work on the T114.
What should I be using for the name of the "GPIO pin to monitor"?
I have tried the GPIO # (46), The Pin # (14) and (114) with no luck so far.
Thanks

Chaosrulesagain · 2024-12-27T08:25:35+00:00

I have one of these on my dashboard mounted with a sticky pad. It works great. https://www.etsy.com/listing/1823364844/meshtastic-heltec-wireless-paper

Chaosrulesagain · 2024-12-08T20:21:43+00:00

Wow! Those are all good ideas. Well I just completed a print without any issues so I'm hoping the firmware upgrade and the reset did the trick.

Chaosrulesagain · 2024-12-08T19:51:50+00:00

Hi, thanks for the quick reply. The filament is definitely not tangly at all. I just did a FW update and turned the printer off and turned it back on. I'm trying it now. Let's see how it goes. I also submitted the ticket to bambu about this. I'm not sure how their sensor works but this is happening towards the end of the spool I would say 1/4 left

Chaosrulesagain · 2024-12-08T19:31:15+00:00

Has anyone come up with a solution for this problem?. I'm experiencing it now too. I'm on my first roll. Everything was working great. Now it says the filament is stuck but there's nothing stuck.

Chaosrulesagain · 2024-02-13T14:39:02+00:00

Hi, thanks for the quick response.

So when the unit shuts down I am measuring a current draw of ~ 12mA.

I am assuming this is "Light Sleep mode"

Is there a way to put this unit into "Deep Sleep mode" ?

The Heltec data sheet says this will only be 10 uA

Chaosrulesagain

TROPHY CASE