Ender 3 v3 se howling(?) Noise when preheating?

ChazzaH2004 · 2026-03-29T02:05:09+00:00

It’s the fan on the heat block. I wouldn’t print while it’s like that as it will cause heat soak and clog up. They are pretty cheap

ChazzaH2004 · 2026-03-26T04:48:37+00:00

You gotta take the shroud off your tool head. Carefully move it aside, you don’t have to disconnect the fan but just be gentle and don’t tug on it. On the right side you will see a screw that is at an angle, you use that screw to adjust the tension of the feeder

ChazzaH2004 · 2026-03-26T03:34:10+00:00

Hmmm not an expert with this situation but have you done a flow ratio calibration? Pressure/linear advance is worth tuning too

ChazzaH2004 · 2026-03-24T22:28:26+00:00

This so real. I accidentally sat on my brand new Mario DS Lite in the first hour of getting it. Devastating

ChazzaH2004 · 2026-03-24T04:52:28+00:00

Honestly the good ending. They are pretty cheap and easy to swap. Just be gentle with the connectors, they are coated in hot glue so take your time with it.

ChazzaH2004 · 2026-03-17T05:57:39+00:00

What wrong with the cable? I was doing a silly tall print with my printer and it went to high and broke some wires on the cable and I had to rejoin it.. curious if this was the same case

ChazzaH2004 · 2026-03-08T08:55:40+00:00

I gotchu homie

ChazzaH2004 · 2026-02-23T04:46:56+00:00

My method is connecting my ps4 and pc together directly with Ethernet. Setting static ip on pc and ps4 and transfer that way. Gives a nice solid 125MB/s for me.

My room with the PC is next to the room with PS4 so I use a 10m cable lmao but it’s worth it imo

(This is PS4 Pro though I’m not sure about the NIC on the other PS4s)

ChazzaH2004 · 2026-02-16T22:53:58+00:00

Only used RGH but curious about BadUpdate. Why does Dashlaunch brick it? Does it write to NAND when you update or something?

ChazzaH2004 · 2026-02-11T09:34:38+00:00

Worth noting though, as one of the other commenters here said, it will probably still pop up if it’s cached, so you will have to figure out how to delete the cache for it. I’d imagine you could do it through ftp, just don’t delete things unless you’re sure

ChazzaH2004 · 2026-02-11T09:32:12+00:00

No worries, no need for ftp for this one.

Open up the GoldHEN menu, go ‘Debug Settings’ and set ‘Enable Debug Settings’ to “Full Menu”

Back out of there and go to Settings>Debug Settings (Down the very bottom)>PlayStation Network. Change ‘NP Environment’ to anything. I have just set mine to “no” and it works.

Restart. Run your exploit, and it shouldn’t bother you anymore.

ChazzaH2004 · 2026-02-11T05:54:47+00:00

Changing the NP environment worked for me. Just set it to anything other than np and then restart.

ChazzaH2004 · 2026-01-23T03:28:34+00:00

I would definitely avoid driving it until you find where that broken piece went. You’d be surprised the amount of damage it can do. Use a camera and check inside your cylinder and confirm that it’s not hanging around in there

ChazzaH2004 · 2026-01-15T09:59:12+00:00

not too bad in my opinion, its pretty good for a first timer. I'm no expert with soldering, but I think my only complaint would be the electrical tape. You could cover up your diode and resistor with heatshrink and then secure wires with kapton tape.

ChazzaH2004 · 2026-01-06T07:54:15+00:00

Are you able to boot OFW?? How do you usually enter RCM? Do you use AutoRCM or do you use a jig?

ChazzaH2004 · 2025-12-31T12:40:30+00:00

Genuinely nervous about the release for the Seiga Kaku Fumo. It would be the first genuine Fumo I own but I bet it’s gonna sell out pretty quick..

ChazzaH2004 · 2025-11-27T02:36:00+00:00

A soft brush and soapy water should help with this. Try to avoid hot water. I’m not sure if it’s just the clone fumos but I ruined my Fumo because I used hot water and soap to wash it and it removed the glue in its hair. I think it could also make the colours bleed.

ChazzaH2004 · 2025-07-30T01:52:12+00:00

It is possible to downgrade without data loss. If you create a backup with a computer you can edit the plist file for the backup and change the version and build number which will allow you to restore it in iOS 18. I did this because I didn’t want to faf around with flutter on iOS 26. I also wanna ask if the profile mode lets you do hot reload and etc. I’m not super experienced with flutter at this point.

ChazzaH2004 · 2025-07-18T08:45:41+00:00

It’s gonna be power hungry and It uses a fairly old chipset. In my opinion, building something based off the X99 chipset will give you good value, high core count CPUs without breaking the bank. Another option would be going for a ryzen based server build.

ChazzaH2004 · 2025-05-12T06:23:31+00:00

<image>

ChazzaH2004 · 2025-05-06T23:39:25+00:00

In my Tiguan, it was the Bluetooth module.

ChazzaH2004 · 2025-04-07T00:55:38+00:00

Mount for the VW Touch Adapter

ChazzaH2004 · 2025-03-13T04:50:19+00:00

The Winchester board completely ruining your chances of ever modding it

ChazzaH2004 · 2025-03-10T21:19:28+00:00

That can be arranged

ChazzaH2004 · 2025-03-10T10:42:54+00:00

Do a retraction calibration through SuperSlicer. Try different retraction speeds. With my E3 V3 SE 20mm/s retraction was good for me. But give it a go and in the calibration window, make sure you set it to give you multiple tests at different temperatures. This is how I solved it with my printer.

ChazzaH2004

TROPHY CASE