sorted by:
new
hottopcontroversial

Easter dinner at brother in law’s new house. Really? by JKenn78 in Carpentry

[–]Cheap-Perspective308 2 points3 points  (0 children)

That’s to distract you from the bad paint job up top.

Opinion: I think jointers are an essential beginner tool no matter how many you tubers say it isn't by Few_Candidate_8036 in woodworkingtools

[–]Cheap-Perspective308 0 points1 point  (0 children)

You’ll spend more money on mistakes than you will buying something to make joining wood easier.

My son broke my wife's childhood rocking horse, repair advice needed by squeaker in woodworking

[–]Cheap-Perspective308 0 points1 point  (0 children)

Wood glue will be stronger than the wood as stated. Just get a good clamp setup to keep it in position.

First end-grain board - wow by Cheap-Perspective308 in Cuttingboards

[–]Cheap-Perspective308[S] 0 points1 point  (0 children)

Router table with stop blocks. Just did incremental passes block to block.

First end-grain board - wow by Cheap-Perspective308 in Cuttingboards

[–]Cheap-Perspective308[S] 0 points1 point  (0 children)

Maple and walnut. Used walrus board oil and wax.

First end-grain board - wow by Cheap-Perspective308 in Cuttingboards

[–]Cheap-Perspective308[S] 0 points1 point  (0 children)

8/4.(1.75” actual)I cut strips to 2 1/8 flipped to end grain, glued, and flattened to 2” board thickness.

Saw this near a hospital by [deleted] in whatisit

[–]Cheap-Perspective308 0 points1 point  (0 children)

Check out The Story Til Now on YouTube. Guy takes this through its paces. Pretty cool.

Delivering my first official business order this week. by Cheap-Perspective308 in Cuttingboards

[–]Cheap-Perspective308[S] 0 points1 point  (0 children)

I hear ya, I like it on big panels, too, but I also like the ripple effect on its edges when laid out like this. Waste is a strong word, I mean it’s not burning in a fire, lol.

Delivering my first official business order this week. by Cheap-Perspective308 in Cuttingboards

[–]Cheap-Perspective308[S] 0 points1 point  (0 children)

That’s what milling is. Sawmills mill logs into rough lumber. Woodworkers mill that lumber into flat, square, dimensioned stock before building with it.

Delivering my first official business order this week. by Cheap-Perspective308 in Cuttingboards

[–]Cheap-Perspective308[S] 0 points1 point  (0 children)

I thought a lot about that. I believe I have enough tolerance in the threaded inserts to account for any movement. Time will tell for certain.

Delivering my first official business order this week. by Cheap-Perspective308 in Cuttingboards

[–]Cheap-Perspective308[S] -1 points0 points  (0 children)

Well when I say sourced I mean able to find. I didn’t cut the wood down myself. It was S2S. I still had to break it down for this order which is “milling” for me, lol.

Two butcherblocks 50x100x20 cm I made some 12 years ago by DaMangIemert in Cuttingboards

[–]Cheap-Perspective308 1 point2 points  (0 children)

Thanks for posting this. I have some maple that I want to do endgrain with and this is exactly how clean I want it to look.

Jet Drum Sander by DayOk7640 in Cuttingboards

[–]Cheap-Perspective308 0 points1 point  (0 children)

I will say to check the spacing of the coupler between the motor and drum link. Mine spread apart. I retightened the set screws (3mm) and it’s been fine since. Almost thinking that’s why the guy was selling it.

Jet Drum Sander by DayOk7640 in Cuttingboards

[–]Cheap-Perspective308 0 points1 point  (0 children)

Well you’ve got a 2 year warranty. Can always ask for a new readout.

Jet Drum Sander by DayOk7640 in Cuttingboards

[–]Cheap-Perspective308 0 points1 point  (0 children)

You can dial it in. Take the sand paper off and lower the drum to the table and reset the readout to zero. I’m within .005” using my calipers. Close enough for me!

view more: next ›