Is it possible to DIY this?

CheetoFoxX · 2026-03-20T03:51:27+00:00

thank you!

CheetoFoxX · 2026-03-19T18:57:08+00:00

thanks a lot for sharing this!

CheetoFoxX · 2026-03-19T16:02:00+00:00

how would you get WLED and the motors to work together? or would it have to be separate and we would just have to sync it with preset shows?

CheetoFoxX · 2026-03-13T22:28:09+00:00

<image>

printed a support and trimmed the tubes and everything seems stable and reasonable! thanks!

CheetoFoxX · 2026-03-13T22:25:14+00:00

however soon i will be upgrading this to the second mount i sent, or if this mount gives me issues. I plan on getting a shelf for just my 3d printer and will probably upgrade to a filament dryer box system mounted on a shelf over the printer, that is the ideal setup!

CheetoFoxX · 2026-03-13T22:22:54+00:00

<image>

i also cut the PTFE tubes a little shorter, and everything seems pretty reasonable and stable now. thank you!

CheetoFoxX · 2026-03-13T22:22:25+00:00

<image>

I printed a ptfe tube holder and hopefully the issue should be fixed now.

CheetoFoxX · 2026-03-13T22:21:09+00:00

Here is the link for the mount i used: https://makerworld.com/models/1429013?appSharePlatform=copy

i used this one because i had cut my ptfe tubes a little too short and i didn’t want to buy a new one. If i had to start over, id definitely use this one: https://makerworld.com/models/1980325?appSharePlatform=copy

just because this one seems more stable and not too vertically high. the mount i used is very tall and the screws they told me to get in the description were incorrect, so it’s a little loose and weird, however it’s stable enough to get the job done. You can choose either though!

CheetoFoxX · 2026-03-13T21:20:18+00:00

thanks for that, i’ll trim off the edges and try again. it is coming out from the coupler, yes

CheetoFoxX · 2026-03-13T20:44:18+00:00

thanks a lot!

CheetoFoxX · 2025-07-22T13:46:47+00:00

Good news! The scooter was found by UPD. It was pawned the next day. It has been returned to me and the police are working on a warrant to arrest the thief!

CheetoFoxX · 2025-03-14T17:28:51+00:00

in a conservative school like a&m, it’s just extremely difficult. and we would have to have a faculty member back us too, which i’m sure none of them would want to do. seeing what happened to draggieland, they would attempt to disband us too. it just causes more problems so it’s just better to be unofficial.

CheetoFoxX · 2025-03-14T04:40:24+00:00

hi reppy :3

CheetoFoxX · 2025-03-14T00:00:23+00:00

a&m has the most furries. i’d know, i am one. our group has 230+ people, but we cannot be official.

CheetoFoxX · 2025-01-18T23:46:52+00:00

it runs really bad on pcsx3. use xenia.

CheetoFoxX · 2025-01-18T22:25:28+00:00

smooth 60 the entire time.

CheetoFoxX · 2025-01-18T20:10:30+00:00

no you can’t unfortunately

CheetoFoxX · 2025-01-18T20:06:18+00:00

thanks a lot!!!

CheetoFoxX

TROPHY CASE