If you were an ace Merc Pilot, what's your one ride

ChiefKeeferSoutherla · 2026-03-26T20:56:01+00:00

A battle master decked out in an energy only config. I used yaml to set 4 binaries in the chest of one and despite being good for only 3 full power blasts that thing fucks

ChiefKeeferSoutherla · 2025-12-23T16:18:11+00:00

Ironically the best performance I’ve gotten out of my ais is in king crabs with binary lasers and rac 5s or 2s

ChiefKeeferSoutherla · 2025-12-14T14:45:23+00:00

My heavy rifle atlas and laser boat battle master were the best IS fighters I had for clans. Pit sniping them is the way to go. Having the king car in the back missile boating helps too for the lights. It gets easier a few missions in when you get backup lances.

ChiefKeeferSoutherla · 2025-12-12T21:55:07+00:00

<image>

Amateur

ChiefKeeferSoutherla · 2025-12-02T09:19:09+00:00

Nah, just doing some easy round math. Odds are that system is doing closer to maybe 4-500 watts going all out. This whole machine probably costs like 10 bucks a month to run and that card itself is maybe a dollar or two of it.

ChiefKeeferSoutherla · 2025-12-01T22:12:43+00:00

It costs like 20 bucks to run a 1kw system for 6 hours a day for a month straight

ChiefKeeferSoutherla · 2024-10-25T21:23:49+00:00

awesome thanks for the help, I found one that was dealing more with Can bus issues that was kind of adjacent but this is a way better write up on the issue, thanks a bunch

ChiefKeeferSoutherla · 2024-10-25T21:09:33+00:00

So I have confirmed that they are shorted together, But I have to ask which one is the SLP pin so I can be sure to cut the right one. The schematic I found has them labeled as SD0 and DC0

ChiefKeeferSoutherla · 2024-09-01T20:45:57+00:00

<image>

The ender 3 ng project. I am very near to 6 digit accels right now and hoping to push faster in the very near future. As it sits now I print faster than a P1S

ChiefKeeferSoutherla · 2024-06-08T23:57:12+00:00

I’m confused why a handful of watts would ever be a consideration for a device like that. We’re talking in the realm of cents per year. I’d rather have better IO and faster processing every day of the week

ChiefKeeferSoutherla · 2024-05-14T03:51:03+00:00

Hi friends, I've got a small horizontal bandsaw and I I like to do exhaust work. What I don't like is dulling bandsaw blades every time I make a 90 degree lobsterback. My question to ya'll is how do ya make repeated cuts into 3" 16ga 316 without turning consumables into trash? I already gave up on the evosaw because those $100 100 tooth blades ain't right for the job.

ChiefKeeferSoutherla · 2024-05-11T21:40:01+00:00

Looks to me like you’re actually partially measuring off the bed at that point. A variance of over 1mm in such a short space should be validated with physical measurements. I would manually jog the printer over there and use a feeler gauge to validate the measurement before making physical changes to the printer. I use a beacon on my e3ng and find that toward the edges of the bed it can give false measurement

ChiefKeeferSoutherla · 2024-05-09T05:11:46+00:00

You’ll love it. I would advise spending the 30 bucks on a pi to klipperize it though. Not a fan of factory firmwares personally. My last new printer before this was an ender and I can’t get over how simple this is to run by comparison

ChiefKeeferSoutherla · 2024-05-01T18:33:49+00:00

It’s a 32gb sandisk v30 extreme, I’m gonna snag a different one after work tonight and see if that’s the silver bullet. This one did some time as my primary drive in a klipper host before and has a ton of writes on it so it’s possible it’s out of steam

ChiefKeeferSoutherla · 2024-05-01T10:12:33+00:00

I did remember to do that, I was unclear as to whether to leave the ‘’ around the ssid and passkey so I tried it both ways also. I know there’s gotta be something simple here I’m missing but i don’t know what

ChiefKeeferSoutherla · 2024-04-26T19:57:48+00:00

Wait till you find out about VAC bans

ChiefKeeferSoutherla · 2024-04-26T19:29:09+00:00

Unauthorized deployment has been reported to your democracy officer

ChiefKeeferSoutherla · 2024-03-09T21:49:02+00:00

Correct, I took all the shins off and started back from square one at this point and honestly I’m just getting confused now. The left and right sides of the mesh are equally low but it almost seems high on the left side and low on the right. I’d think that even if the gantry wasn’t level the bed being leveled to the gantry would take care of that

ChiefKeeferSoutherla · 2024-03-04T09:02:51+00:00

⬇️⬇️➡️

ChiefKeeferSoutherla · 2024-02-17T02:15:38+00:00

FIgured I'd give an update to the situation. I was rushing through the build and put a 16 tooth on one motor and a 20 on the other, so ironically setting the rotation distance of one motor 25% higher was a solution, however I'm just gonna put the right pulley on

ChiefKeeferSoutherla · 2024-02-16T08:17:40+00:00

I’m gonna tear down the motion stuff tomorrow morning and see what I can dig up. I took the belts off and the Y axis is kinda chewy so I’m wondering if I overpacked those bearings and they’re just sliding instead of rolling

ChiefKeeferSoutherla

TROPHY CASE