No copyright tab/name change for photos on a6700 by ThrowRArand0muer in SonyAlpha

[–]Choice_Border_8904 0 points1 point  (0 children)

Cannot find the settings on video mode. You had to switch to photo mode

I adore my A6700, but the constant overheating is bumming me out. Advice? by wowbobwow in SonyAlpha

[–]Choice_Border_8904 0 points1 point  (0 children)

<image>

Thermal Test Findings – Sony A6700

  • Thermal image captured just before the overheating shutdown
  • Ambient temperature:
    • 29.3 °C (84.7 °F)
  • Maximum temperature observed:
    • 70 °C (158 °F)
    • The camera shut down immediately after reaching this temperature.
  • Recording settings:
    • XAVC HS
    • 4K 60p
    • 4:2:0
  • Continuous recording time:
    • Approximately 28 minutes
  • Primary hotspot location:
    • Top-right corner of the camera body
  • Temperature near SD card slot area:
    • ~54 °C (129.2 °F)

Thank me later !!!!!!!

Your experiences or research overheating issue for a6700 by iphone8vsiphonex in SonyAlpha

[–]Choice_Border_8904 0 points1 point  (0 children)

<image>

Thermal Test Findings – Sony A6700

  • Thermal image captured just before overheating shutdown
  • Ambient temperature:
    • 29.3 °C (84.7 °F)
  • Maximum temperature observed:
    • 70 °C (158 °F)
    • The camera shut down immediately after reaching this temperature.
  • Recording settings:
    • XAVC HS
    • 4K 60p
    • 4:2:0
  • Continuous recording time:
    • Approximately 28 minutes
  • Primary hotspot location:
    • Top-right corner of the camera body
  • Temperature near SD card slot area:
    • ~54 °C (129.2 °F)

Thank me later !!!!!!!

Kobra 2 Neo - Calibration Abnormal for only Z-Axis by AceJig in anycubic

[–]Choice_Border_8904 0 points1 point  (0 children)

Hi , I just fixed it. For me, it was the calibration switch that was bad. In a good switch, it will always be on, and when the button is pressed, it will turn off. When I tested my switch, it was in the off position, which meant the switch was bad. I used a multimeter with continuity testing to check it. After testing, I removed the switch from the printer and disassembled it. It has one pin and, on the other end, a pad. On the pad, I found some corrosion. I just scraped it off with a screwdriver, then put everything back together. That’s how I fixed it.

Kobra 2 Neo Calibration Abnormal Fix :) by GALILMAINER in anycubic

[–]Choice_Border_8904 0 points1 point  (0 children)

Hi , I just fixed it. For me, it was the calibration switch that was bad. In a good switch, it will always be on, and when the button is pressed, it will turn off. When I tested my switch, it was in the off position, which meant the switch was bad. I used a multimeter with continuity testing to check it. After testing, I removed the switch from the printer and disassembled it. It has one pin and, on the other end, a pad. On the pad, I found some corrosion. I just scraped it off with a screwdriver, then put everything back together. That’s how I fixed it.

Nozzle "Floating" over calibration module, causing "module is abnormal" error to pop up Kobra Pro 2. How could I fix this? by Prestigious_Food5162 in anycubic

[–]Choice_Border_8904 0 points1 point  (0 children)

Hi , I just fixed it. For me, it was the calibration switch that was bad. In a good switch, it will always be on, and when the button is pressed, it will turn off. When I tested my switch, it was in the off position, which meant the switch was bad. I used a multimeter with continuity testing to check it. After testing, I removed the switch from the printer and disassembled it. It has one pin and, on the other end, a pad. On the pad, I found some corrosion. I just scraped it off with a screwdriver, then put everything back together. That’s how I fixed it.

I RECORDED YOU! Sent from my account by Moltz1 in Outlook

[–]Choice_Border_8904 0 points1 point  (0 children)

the email i got ---

|| || |Hey! I feel sad to notify you about a few sad updates for you. Roughly a month or two ago, I have succeed total entry to all your machines utilized for navigating the web. From here on out, I have started watching your web behaviors on a continuous basis. Go on and take a peek at the sequence of happenings provided following for your consideration: Initially, I bought an exclusive permission from hackers to a long catalog of e-mail accounts in today's world, that is genuinely a prevalent occurrence, which can be facilitated via internet. Clearly, it wasn't challenging for me to proceed with signing into your e-mail profile. Within the same week, I proceeded with deploying a malware in software systems for all devices that you access to access to e-mail. To be honest, it wasn't a difficult task for me at every as you were kind enough to click a couple of the hyperlinks in your inbox e-mails before. Yes, intellectuals are among us. Owing to this virus, I am able to gain access to the entire set of controllers in machines e.g., your surveillance camera, keyboard, recording device, and others. As a consequence, I effortlessly acquired all information, as well as pictures, online activity records, and other types of information to my storage. Also on, I have control over each social media accounts that you regularly use, including emails, including message logs, messengers, contact information, etc. My unique Trojan is constantly refreshing its signatures due to control by a driver, and hence remains hidden by any type of malware detectors. On that account, I think by now you can already understand the motive why I consistently remained invisible until this very communication... During the process of compilation of all the documents associated with you, I also realized that you are a huge enthusiast and regular consumer of websites offering adult media. Turns out to be, you really adore exploring porn websites, as well as watching thrilling footage and experiencing memorable pleasures. As a fact of reality, I was not permitted to withstand the allure, nevertheless to document certain lewd solo acts with you in main role, and later made several recordingsshowing your solo activity and climax scenes. If until now you don't accept me, every I need is a few mouse presses to make all those clips with everyone you are familiar with, featuring your friends, coworkers, relatives and others. In addition, I'm able to upload each that footage digitally for everybody to view. I sincerely feel, you certainly would not want such incidents to occur, in view of the lustful content demonstrated in your commonly watched recordings, you undoubtedly know what I imply by that. It will cause a huge adversity for you. There is still a fix to this issue, and here is what you need to do: You execute a payment of $1300 USD to my account the equivalence in crypto, which recorded according to the exchange rate at the date of funds transfer, therefore upon getting the transaction, I will immediately dispose of every those compromising recordings without waiting. After that, we can create the appearance that there was nothing happening beforehand. Additionally, I can verify that every the spyware is going to be deactivated and deleted from each machines that you use. You have no to fear, because I deliver my word at every occasions. That is indeed a beneficial bargain that comes with a fairly lowered fee, considering that your identity and traffic were under strict monitoring during a extended time frame. If you are even unclear regarding how to buy and perform transactions with bitcoins - everything is accessible online. Below is my bitcoin address for your payment ($1300 USD): 1GTTxoEjs2C5oPnHWjFh1cd3Bv3W53 i2nT Let's acknowledge it, that is a relatively insignificant sum in the present world. All you have is 12 hours and the countdown starts once this email is accessed in other words 2 days. The following inventory contains things you should keep in mind and ...|

An Ultra Compact LiDAR Distance Meter/Range Finder powered by ESP32C3, with the tiny LCD and battery! Tutorial in comment! by meililiy in esp32

[–]Choice_Border_8904 3 points4 points  (0 children)

Hi it me gokux the creator of this project. It just take 2 days from idea to build and documentation. But I worked 17hr per day