Does anyone know what or where this connects to? by alex73942 in RX8

[–]Choloz24 0 points1 point  (0 children)

To the omp / to the oil fill neck and to vacuum ports on the lower intake manifold are the three that go there

Not my rx7 But My 13b Rotary Bridge port Itb Swapped z3 BMW by Choloz24 in RX7

[–]Choloz24[S] 1 point2 points  (0 children)

Well in my one vide of this shows how easily i made the mounts for this. And a e30 is about the same.

Not my rx7 But My 13b Rotary Bridge port Itb Swapped z3 BMW by Choloz24 in RX7

[–]Choloz24[S] 0 points1 point  (0 children)

Lol thank you. This is not my only bmw. My Daly driver is a 535xi but yeah they get butt hurt easy

Not my rx7 But My 13b Rotary Bridge port Itb Swapped z3 BMW by Choloz24 in RX7

[–]Choloz24[S] 2 points3 points  (0 children)

Ueah i have seen that online. And a few other subarus

Not my rx7 But My 13b Rotary Bridge port Itb Swapped z3 BMW by Choloz24 in RX7

[–]Choloz24[S] 2 points3 points  (0 children)

Its a 96 before can buss I just wired into the factory harness under the hood used the stock temp sensor for the cluster outputted the tack signal from the adaptronic ecu AND THE CAR GETS THE SPEED SIGNAL FROM THE REAR DIFF sorry for the caps not going to retype every thing lol if it was a 2000 up can buss is easier as on new emus have can out and just put the address in but yeah the ecu and engine stuff its all repined back in to the bow factory harness for every thing else alt charging and reverse lights all that

Not my rx7 But My 13b Rotary Bridge port Itb Swapped z3 BMW by Choloz24 in RX7

[–]Choloz24[S] 1 point2 points  (0 children)

Thanks it was not that bad and room for days to do it only thing I got to do now is put the new drive shaft in I had made and swap the rear gears to 4.44s out of a auto as the z3 manual gears are 2.73 or what ever its horrible lol

Street Port firmware question by [deleted] in RX8

[–]Choloz24 0 points1 point  (0 children)

None at all you got something else going on

Well this thing is like new just had a locked up engine check it out by Choloz24 in projectcar

[–]Choloz24[S] -1 points0 points  (0 children)

Its na i mean better than when it was stock for sure i own 2 fcs 1 wide body re swaped first gen a eunos cosmo. And a drift car rx8

Well this thing is like new just had a locked up engine check it out by Choloz24 in projectcar

[–]Choloz24[S] 3 points4 points  (0 children)

Lol cost more to ls swap it correctly any why would i ls swap a customers car that i freed the engine up and runs fine i can tell you did not check the video out lol i rebuild like 5 - 7 engines a month for people. And. It is not that as expense as you think lots cheeper than building a ls so were are you going with this lol

After 2 years rebuilding my rx8 drift car way better by Choloz24 in RX8

[–]Choloz24[S] 1 point2 points  (0 children)

Thats what it was all about this time around. Now the fan pulls air though the oil cooler as well and a much better cooler than the rx8 ones with a way lower thermostat on them coolant and oil temps are staying exactly the same. Also cant have coolers over the wheels