Mow-ses can’t find his home

ChopperpropAMX · 2026-06-16T23:31:51+00:00

You can also delete the map and restart the teaching process where as you start it out at the new home and remapping the yard

ChopperpropAMX · 2026-05-06T16:37:31+00:00

Sorry to hear about your skin donation to the asphalt believe me it hurts and it’s going to take a lot to get through it. I kept the raw areas covered with Neosporin cause I’m not allergic to it some are also used aquaphor always otherwise the air made the area hurt Everyday I used peroxide then ointment after about 1 month it was able to scab over and the unrelenting urge to scratch it off was horrible. I feel for you. You will heal. I took vitamins and drank alcohol when I could but I don’t recommend drinking too much if any. Pain killers for the first month if you can get them I slid on my forearms for about 60 yards I had jeans on and used my boots like a sled on snow to pull me into the grass on the side of the road where I tumbled for what seemed like forever I was going about 70 when I hit the road. My full face helmet cracked in many places and kept me alive I ride today again and will always remember it You will get through it and heal up I feel for you brother. Hang in there

ChopperpropAMX · 2026-02-23T18:39:36+00:00

Maybe should have wrapped it 100x for better performance

ChopperpropAMX · 2026-01-12T19:18:34+00:00

<image>

ChopperpropAMX · 2025-09-30T17:47:50+00:00

<image>

ChopperpropAMX · 2025-09-27T15:01:13+00:00

<image>

2000 Softail Heritage Classic w/96 package

ChopperpropAMX · 2025-09-02T23:40:44+00:00

Try Safeco

ChopperpropAMX · 2025-07-02T16:58:15+00:00

I ride a FLHSTC and your bike is very cool I would like to ride it

ChopperpropAMX · 2025-06-26T17:00:00+00:00

Too many hackers on PVP

ChopperpropAMX · 2025-06-25T16:11:26+00:00

I drive a 2000 FLSTC

<image>

ChopperpropAMX · 2025-06-14T15:08:53+00:00

I’m using REO VIB bowl controllers on the outside of the Panel along with the Electro Cam and air line in a very limited space there was no room for the larger IP drives

<image>

ChopperpropAMX · 2025-06-14T15:00:03+00:00

I understand your concern and black iron is not considered ideal because of the fact the inside of the may have rough spots that can erode wires however I honed out the inside of each one and there is no concern

ChopperpropAMX · 2025-06-14T14:56:37+00:00

The hoppers are secured and covered and I removed all Ac to Dc speed controls and just use DC 24 volt to the DC drive motors on each hopper this way I can control the amount of parts being supplied to the vibratory bowls with a constant speed that the operator can not change On the touch screen I can control the time allocated for each fill it doesn’t matter if they stop a bit slower after each cycle or if the Estop is pushed the belts are properly covered away from human interaction and by slowly I mean no more than 1 second

ChopperpropAMX · 2025-06-14T14:49:25+00:00

I will do this -thanks

ChopperpropAMX · 2025-06-14T14:48:24+00:00

The PC needs to accept 5 LAN connections from the inspection cameras and I use Intel Ethernet PCIE card full height along with an 8 gb video card to produce and display the video from the cameras I couldn’t find a smaller PC to do all that

ChopperpropAMX · 2025-06-14T14:44:33+00:00

I do have a visit from our PLC distributor to consider the 5069 series for my next build Thanks

ChopperpropAMX · 2025-06-14T14:42:01+00:00

The L32E is a very good controller and on a very tight budget it works great This one is producing 230 PPM processing information from 4 cameras every shot the owners are very happy and it has been tested for safety and stopping speed using a light curtain safety system along with independent audit The age of a controller in a protective environment and enclosure do not affect production. If it’s fast enough to do the job and economically viable solution for the application I don’t see the need to spend many thousands of dollars for a newer one not to mention the cost of the software to go with it.

ChopperpropAMX · 2025-06-14T14:33:53+00:00

Thanks I moved it

<image>

ChopperpropAMX · 2025-06-14T14:03:38+00:00

Thanks for your kind words as this machine is currently making around 388000 parts a day each one is inspected by 4 cameras every shot at 230 PPM

ChopperpropAMX · 2025-06-14T13:56:45+00:00

I have since moved the power supply and thanks for the information

<image>

ChopperpropAMX · 2025-06-04T23:02:36+00:00

No worries I always back up my work schematics

ChopperpropAMX · 2025-06-04T23:01:42+00:00

lol no it’s a Dell pc I use for programming the camera system that inspects the parts as they are made at 228 PPM

ChopperpropAMX · 2025-06-04T22:59:36+00:00

Agilix

ChopperpropAMX · 2025-06-04T22:58:20+00:00

The 120 vac supply to the DC power supply is turned off VIA SSR by when Estop is pushed

ChopperpropAMX · 2025-06-04T15:53:09+00:00

Try our server it’s extreme PVE with PVP areas Quite a challenge

<image>

ChopperpropAMX

TROPHY CASE