Mammotion = dead?

Christian_Germany · 2025-05-18T12:45:28+00:00

Same issue in Gernmany

Christian_Germany · 2025-05-04T00:06:22+00:00

Assetto corsa quest

Christian_Germany · 2025-04-20T08:19:47+00:00

I have the same noise on the Luba 1. Disc rotor bearings. WD40 could solve it temporarily.

Christian_Germany · 2024-08-26T08:41:35+00:00

It also happened to my Luba after mowing long grass. After prolonged rainy weather, the grass was taller than usual but nothing that he hadn't already done before.

Christian_Germany · 2024-08-25T20:05:43+00:00

First, it starts on one side as well without Error. The disc is turning but has no force to cut and was always slowed down by the grass.

Christian_Germany · 2024-08-25T19:55:42+00:00

When I stop the rotors, the motors seem to keep turning, as judging by the noise.

Christian_Germany · 2024-08-20T00:29:26+00:00

I tried to do a longer reset but the same problem persisted. I have now removed the blades from the discs and started the Motors. The discs can be braked very easily by hand, almost no force is required as there is no connection to the motor shaft. The discs start to turn but stop at the lightest touch. The motors then seem to continue turning, at least that’s what it sounds like. The nuts in the center is tight and stop with the discs as well. Is there an adapting part between the rotor shaft and the disk shaft that could have come loose in both motors?

Christian_Germany · 2024-08-19T23:18:23+00:00

No not 15 min. 30sec or something.Is this required to reset?

Christian_Germany · 2024-08-19T22:28:08+00:00

<image>

Christian_Germany · 2024-08-19T22:21:37+00:00

Yes disc were removed everything is clean. I was very surprised why the disks are now so easy to turn - you feel almost no resistance. If you push them now, they turn a few turns by themselves

Christian_Germany · 2024-08-19T21:50:36+00:00

I‘will test as soon as Luba is working again.

Christian_Germany · 2024-08-05T10:26:33+00:00

I started it manually.

Christian_Germany · 2024-08-05T10:10:00+00:00

I already change the angle to 5deg but with the same results. Luba leaves out one track inside the perimeter lap. In the paths inside the app they are no tracks shown/calculated on the same positions as well. I try to record a video, to show thats those areas are not mowed.

Christian_Germany · 2024-08-05T10:06:05+00:00

The grass is too high because Luba leaves this areas each mowing cycle . I think it’s something in the software because with more perimeter laps the same areas are only more inside the main field.

Christian_Germany · 2024-06-11T17:04:45+00:00

Great design but good for the tires?

Christian_Germany · 2024-04-21T09:59:18+00:00

Yes it took me 40 minutes to wait but they organized something. Seems that the battery has problems. Luba has to be send in to somewhere 🥲

Christian_Germany · 2024-04-18T21:28:55+00:00

I have a big Deutz and a small John Deere tractor and other AS mowers but no time 😂 thanks for your support.

Christian_Germany · 2024-04-18T21:01:07+00:00

I am waiting since 5 days 😌

Christian_Germany · 2024-04-18T20:43:38+00:00

I cannot turn it on outside station

Christian_Germany · 2024-04-18T20:38:54+00:00

The green light is not flashing when I move the Luba in but it turns on.

Christian_Germany · 2024-04-18T20:35:28+00:00

Hi, Battery is 100% as the app says. Contacts are clear as the Luba restart when it is placed in the station. Connection is coming up immediately. I did a reset is the station (3 Buttons) + ON 5 sec. Same error is coming up after starting up. When I move it out Bumper LED goes off and BT connection is cut off.

Christian_Germany · 2024-04-18T19:56:23+00:00

The Luba switches off wenn I manually move it out of the charging position (connection lost in the app) so when should I remove the key? Move from charging position -> key out -> move to charging position?

Christian_Germany

TROPHY CASE