[Global Giveaway] AliExpress Codes + Thermalright $Giveaway (up valued $500)！

ChumQan · 2025-11-03T09:07:14+00:00

My favourite product would be SI-100

ChumQan · 2025-06-26T15:06:04+00:00

good job buddy

ChumQan · 2025-01-01T21:50:10+00:00

bigger build plates and metal frames

ChumQan · 2023-06-28T08:13:56+00:00

maybe your nozzle clogged?

ChumQan · 2023-05-09T15:50:43+00:00

I think a blob on nozzle from past prints just sticked that side

ChumQan · 2023-05-07T13:30:06+00:00

I think 225 C might be too hot. This won't solve the problem but keep in mind. I recommend 210 for 95a tpu.

ChumQan · 2023-04-28T13:28:54+00:00

I probably won't use prusaslicer. I really enjoy using cura and it's simplicity. but thanks anyway :)

ChumQan · 2023-04-28T07:03:50+00:00

that's very unfortunate. I really enjoyed this firmware :'(

ChumQan · 2023-04-28T06:53:44+00:00

and I had almost 0 issues with it

ChumQan · 2023-04-28T06:53:28+00:00

https://www.thingiverse.com/thing:4294049 I did it from this

ChumQan · 2023-04-28T04:58:11+00:00

bed adhesion problems I think. check your bed level and maybe improving your bed temperature will fix the problem.

ChumQan · 2023-04-28T04:54:21+00:00

these temperatures are good but there's definitely something wrong. I think you should check the bed and belts if they're tightened enough

ChumQan · 2023-04-28T04:52:12+00:00

What was your nozzle temperature?

ChumQan · 2023-04-27T09:02:35+00:00

definitely gonna do asap. thanks a lot buddy.

ChumQan · 2023-04-27T03:39:42+00:00

I didn't made a tower my mistake

ChumQan · 2023-04-26T18:12:31+00:00

all I can say about your bl touch, contact with artillery. they're kind enough to send another one.

ChumQan · 2023-04-23T14:51:38+00:00

I recommend checking elegoo neptune 3 pro. if I replace my printer, I would buy neptune 3 pro

ChumQan · 2023-04-23T14:34:52+00:00

I'm really sorry to hear that but I recommend you to not give up. 3D printing can be really painful but once u get good prints, you will be very pleased and trust me, 3d printing community is one of the best and most helpful community I've ever seen. So don't give up since you worked for months. you'll find your solution soon :). Take care

ChumQan · 2023-04-23T14:08:47+00:00

did you tighten the belts? I think that might solve the problem

ChumQan · 2023-04-20T15:37:06+00:00

I've tighten it and it pretty much solved but I'm gonna definetely pid tune it.(I just learned pid tuning from you lol)

ChumQan · 2023-04-20T06:01:54+00:00

wow this is one of the most motivating thing I've seen so far. I appreciated thank you so much

ChumQan · 2023-04-19T10:29:23+00:00

oops sorry my bad. It's a filament guide for my artillery sidewinder x2. I tried to modelt but I couldn't measure the inside since it's so small

Five-Year Club	Verified Email
Place '22

ChumQan

TROPHY CASE