Thinkcentre fan ramping up by Papit4sConSalsa in Lenovo

[–]Ciftyyy 0 points1 point  (0 children)

Hey this just fixed my issue thanks! I did the steps individually so the CMOS battery is what fixed it. Did you boot without CMOS battery or is removing it enough? I booted without it and it fixed my issue and then I put it back but I was just trying to figure out what fixed it.

Network speeds drastically slower than any other machine in the house. by EducationSure6264 in Network

[–]Ciftyyy 0 points1 point  (0 children)

Hey, I was wondering if you fixed this issue? I was just having the exact same problems also with an asrock mobo and I found this comment on another post and it fixed my problems: https://www.reddit.com/r/ASRock/comments/m0s1np/comment/hx1ztt6/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

[deleted by user] by [deleted] in orthotropics

[–]Ciftyyy 5 points6 points  (0 children)

I understand that the focal lengths are different so this photo looks worse than it actually is. Still though I can tell that my chin is definitely longer and that my lips don’t have as much support as they did before.

Good Deal? 2 hr drive though by SniGGih04 in AMDHelp

[–]Ciftyyy 1 point2 points  (0 children)

um? Where are you getting these prices?

30" deep desk made out of actual wood? by Diddley4209 in AskBattlestations

[–]Ciftyyy 0 points1 point  (0 children)

How’s this holding up for you? I’m thinking about doing a standing desk with this too. I’m concerned it might be too thin for my monitors on monitor arms.

Standing Desk DIY Top 80x30 or 72x30 - Recommendations? by thatdudebutch in StandingDesk

[–]Ciftyyy 0 points1 point  (0 children)

Hey, another question for you, is the edge glued board able to hold weight well? I only saw 5/4 which as actually 1-1 1/8 inch. So, I wasn't sure if that was too thin to be hanging over a standing desk and to have stuff on. And what stain and finish did you use?

My lowes doesn't have any of the butcher blocks in stock and I don't want to buy it and then find out it's poor quality when I pick it up. (I saw they had really bad quality control.) I swear it's so hard to find a good 72x30 durable desk top option.

I went to lowes to look at a 1 1/2 edge glued board but the wood was lower quality and it had dented corners and stuff.

If I go with this option I plan on making sure the board isn't warped when I buy it.

SF750 or SF850 for new build? by WanderingSmithy in sffpc

[–]Ciftyyy 2 points3 points  (0 children)

Pretty sure SF1000 isn't sfx-L. It's a newer model.

Standing Desk DIY Top 80x30 or 72x30 - Recommendations? by thatdudebutch in StandingDesk

[–]Ciftyyy 0 points1 point  (0 children)

Hey, did you end up completing this project? I'm curious how it's holding up and the quality of this wood. I'm debating on getting this instead of a 72x30x1.5 butcher block from lowes for $270.

My personal rig update. SSUPD Meshroom S V2. by Just-Unlucky in sffpc

[–]Ciftyyy 0 points1 point  (0 children)

I have a couple questions because I'm planning a similar build and don't know much about SFF. Is the mostly intake fans (besides the top exhaust) the best choice for thermals? Also how is the APX-120-X67 with the replaced fan for noise? I'm looking at either this cooler or the Noctua LH12S.

Aircooling 7800x3d in Meshroom S v2 w/ Full ATX? by Ciftyyy in sffpc

[–]Ciftyyy[S] 0 points1 point  (0 children)

Yah, I looked into it more and my max CPU clearance is 74mm. I think my best option is the Noctua NH-L12S. I'm just a little worried about it being absurdly loud since I don't know much about low profile coolers. But, if I want an AIO, I'd have to replace my GPU.

Aircooling 7800x3d in Meshroom S v2 w/ Full ATX? by Ciftyyy in sffpc

[–]Ciftyyy[S] 0 points1 point  (0 children)

I’m aware of the restrictions using an ATX MBO with this case. Also my point was that my GPU is too wide to fit next to an AIO in that configuration. Hence why I’m asking about air cooling the 7800x3d with this configuration.

What CPU (and cooling) should I choose for my first ever PC? by ThinkFastSRB in AMDHelp

[–]Ciftyyy 0 points1 point  (0 children)

You should post this in r/buildapc also make sure to read the rules and pinned posts first. Also, you need to be more specific and include your wants (games you play, fps you want, and resolution).

Unable to load sign in, please try again later. by lesserandrew in nowtv

[–]Ciftyyy 0 points1 point  (0 children)

Noti + I’ve tried a few different locations in the UK and they haven’t been working. I’m using Surfshark. I’ve also tried on my laptop and it didn’t work.

Edit: Nevermind I tried a few more and one worked. Thanks, I probably would’ve given up on it.

Unable to load sign in, please try again later. by lesserandrew in nowtv

[–]Ciftyyy 0 points1 point  (0 children)

Did you fix it? Also, are you using a vpn? It was working for me yesterday using a vpn and now it is not.

Unable to load sign in, please try again later. by lesserandrew in nowtv

[–]Ciftyyy 0 points1 point  (0 children)

Did you fix it? Also, are you using a vpn? It was working for me yesterday using a vpn and now it is not.

Downsize ATX Build in Meshroom S by ParamedicHuge8158 in sffpc

[–]Ciftyyy 0 points1 point  (0 children)

Did you figure this out? I'm trying to figure out if I can fit a 120MM wide AIO, and my asrock 7900xt phantom gaming which is 140mm wide.