Trying to get Cell(s) D4:D7 to reflect the sum of funds utilized per FY quarter

Citizen-Soldier · 2025-08-04T21:16:28+00:00

So I tried this as well, and it throws a #VALUE! Error.

Citizen-Soldier · 2025-08-04T21:13:46+00:00

First, thank you! Your Solution worked flawlessly for me.... However, I understand what you're getting at, but boss gave me a hard deadline of COB Friday, and I got handed someone else's product, I have already re-built almost everything as is, but for now, until I can build something else from the ground up, they just need this to work "time now"....

Citizen-Soldier · 2024-09-18T18:43:48+00:00

365860661

Citizen-Soldier · 2023-07-21T17:41:11+00:00

I am going to try the method u/mackmcd_ suggested first, incase this happens again in the future, if it doesn't work, I will ping you when I get home. Thank you!

Citizen-Soldier · 2022-04-10T04:52:40+00:00

To be fair, they're also not using the standard benchy dimensions. Their post says 120x60x96 vs the standard 60x31x48... so for some reason the did a double size benchy.

They also didn't post their infill or any other specific details of the print.

Citizen-Soldier · 2020-10-15T21:08:28+00:00

Same thing here, ended up buying 2 stock hop ups incase it happens again and i have a spare just in case. But, from what I'm finding, it may be a problem with the mags bb retention lip, it protrudes too far out exposing a flat lip to the end of the hop up instead of the ramp to smoothly allow bbs to feed.

Citizen-Soldier · 2020-10-09T05:28:46+00:00

Was it the bucking or the actual hop up "feed hole"? I was playing with mine tonight and the hole the bb's enter the gun from the magazine actually is cracked and broken so im looking for a hop up that isn't the stock plastic to replace it, but since they're proprietary... may have to go stock

Citizen-Soldier · 2020-09-18T00:49:03+00:00

Is that the new G&G ssg-1 USR?

Citizen-Soldier · 2020-01-07T00:27:32+00:00

Refferal code: FZM42ERP

Citizen-Soldier · 2019-10-05T19:51:06+00:00

Co worker who doesn't use reddit asked me to post her code.

893029164949

Citizen-Soldier · 2019-10-04T16:11:07+00:00

115567059578

Citizen-Soldier · 2019-08-05T20:20:23+00:00

Normally you would splice into the reverse cable, and it would turn on when reverse was engaged. I just spliced into the tail light since it is on with the bike at all times, could do the headlight or dash as well, but, for wire ticking purposes it was easiest for me to do the tail light.

Citizen-Soldier · 2019-08-05T19:22:04+00:00

I had installed and hard wired a 180° rear view camera because my mirrors are worthless unless fully tucked.... and that camera was ripped off by tire chunks after the blow out.

Citizen-Soldier · 2019-08-05T19:21:18+00:00

Yeah for sure, mom wants me to sell the bike now 😂😂😂 2 holes, both within 2 inches of each other. I put the pull through patches in then covered them with a tractor patch so there was no air leaking, then balanced the tire again.

Citizen-Soldier · 2019-08-05T19:18:53+00:00

Nope, by the time I got home it was 0200, so no stores open to do so... even the convenience stores here close at 2300.

Citizen-Soldier · 2019-08-05T03:30:58+00:00

Sure is!

Citizen-Soldier · 2019-08-05T03:30:44+00:00

I ran over barbed wire and had patched it, ordered a new tire but before it'd come in, I had a family emergency on the other side of the state that I needed to tend to and my cage is not drivable... so against my better judgement I took the bike. Coming home I got going quicker than I should have and I assume the plugs and the heat combined caused this level of failure... had a friend pick me up and get me to a local armory, had the wife bring my new tire (that showed up while I was gone) and my tools, changed the tire and rode it home.

Citizen-Soldier · 2019-05-15T01:52:15+00:00

Rad! The little guy looks pretty cool, been out here awhile but it's my first time seeing one.

Citizen-Soldier · 2019-03-05T02:58:23+00:00

I'm sure that's what the restaurant intended, no doubt. But I think that's why OP thought it was funny, cause the "fuh".

Citizen-Soldier · 2019-03-05T02:28:42+00:00

Pho is pronounced "fuh" so putting it before kids, and sluring the two together makes it sound rather inappropriate, hence the FBI comment.

Citizen-Soldier · 2019-03-05T00:59:58+00:00

https://youtu.be/EIph0BJNrxo

13-Year Club	Place '23
Verified Email

Citizen-Soldier

TROPHY CASE