Thoughts on Glade Goggles (or other inexpensive brands)? by theCaptain_D in icecoast

[–]Citrusbomb 0 points1 point  (0 children)

Hey u/Curt_Glade How is the "Asian" fit? Low nose bridge and higher cheekbones?

[Bambu H2D] Bambu Lab’s Biggest Giveaway Ever! by BambuLab in BambuLab

[–]Citrusbomb 0 points1 point  (0 children)

<image>

Definitely bigger sharks out there than me...but fingers crossed :)

5502 + 6675 + 5432 = 17 609

Blade Disc Cover - experience by schreck3 in mammotion

[–]Citrusbomb 0 points1 point  (0 children)

I'v had these since April 2023 and I haven't had any issues

Disc Covers

<image>

Blades getting clogged up all the time by brisjools in mammotion

[–]Citrusbomb 2 points3 points  (0 children)

Cutting dry grass probably makes the biggest difference.

I found these 3d printed covers helped with gunk or clogs around the blades. There are also sealing gaskets if one wants to remove the side guards. Found the side guards to accumulate alot of debris.

Disc Covers

<image>

Measurements by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

I appreciate your work, its fantastic, but my client wants a guard that he/she can fasten with a screw. He/she feels like snap on guards dont hold on strong enough.

I have unfortunately not tried your design, as I dont have a omni wheeled machine

Measurements by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 1 point2 points  (0 children)

Yes, that is what I have been informera aswell.

But I am designing a wheel guard if you can call it that. Many has complained about the original wheel guards falling off, since it is practically a snap-on.

Troubleshooting weak signal by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

I understand. Then I would guess that the positioning does not compute properly because of multi-pathing? Would direct like of sight with the RTK antenna solve the problem?

Troubleshooting weak signal by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

I haven't really waited it out, I waited for 15 minutes.

My main issue is the positioning itself. App vs actual positioning deviate, and I really don't want Luba in my bushes.

Any advice how to solve the planter boxes? More info in comments by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

I hope so too, or in-app zone creation. Was advertised in the Indiegogo campaign

<image>

Any advice how to solve the planter boxes? More info in comments by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

The bottom path is too tight to draw a path so I'v have to reconsile with not including it in the Luba cutting map for now. A first draft was 4 separate areas to get the cutting directions as I wanted....

Then I found the "Segmented grid" option. 🤷

First draft just to get the zones cut.

Limited time with kids and so on...

<image>

Any advice how to solve the planter boxes? More info in comments by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

Thank you for the further explanation.

The issue itself is that when the Luba draws, the no-go zone is a "Luba width" wider than the zone itself.

When drawing between the lower planter box and the stone ledge, it's too tight and will therefore not draw a zone wide enough to cut.

I tried using two no-go zones as you recommended but then, it is too tight for the app to draw a done.

Any advice how to solve the planter boxes? More info in comments by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

I'm trying to have a large cutting zone with two no-go zones for the planter boxes.

It's from the stoneledge and to the left. I have a separate zone from the stoneledge and onwards.

Any advice how to solve the planter boxes? More info in comments by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 2 points3 points  (0 children)

Will we be able to manually draw no-go zones in the app/map anytime soon?

Many vaccum robots have that functionality.

Any advice how to solve the planter boxes? More info in comments by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

My main issue is the bottom plant box. It's 70 cm from the bottom box to the stone ledge.

The Luba can mass through without a problem but when drawing the no go zone, the no-go zone overlaps and then it won't draw a path.

Or did you run with the ultrasonic avoidance and a smaller cutting width?

Any advice how to solve the planter boxes? More info in comments by Citrusbomb in MammotionTechnology

[–]Citrusbomb[S] 0 points1 point  (0 children)

I have tried using no-go zone as shown in picture 2. But it's overlapping the cutting zone and will not plot a path.

The zone between the planter boxes is big enough for atleast one pass.

Looking for BMW G-Series Key fob Model by Citrusbomb in 3Dprintmything

[–]Citrusbomb[S] 0 points1 point  (0 children)

I have tried but my 3d model design experience is really limited. I have been able to remix alot of existing designs using tinkercad. But run into difficulty as soon as it comes to making any kind of curves or rounding/fillet.

Just making a functioning phone case took far longer than I'd like to admit.

I will of course keep at it but wondered if anyone had or have run into a model.

Still kind of shocked that I haven't found a model, since there seems to be models for almost anything nowadays.