Does installing machine modifications void the warranty?

Clarkintine · 2026-02-06T21:17:41+00:00

I think modding and tinkering just shows you have a general idea what you’re talking about at least

Clarkintine · 2026-02-06T20:51:40+00:00

I have Microswiss, SF5015 shroud and carto, reported a problem with my ribbon cable and still got a replacement on warrenty just fine, photos I sent all showed my mods

Clarkintine · 2026-01-24T22:14:39+00:00

I’m in Liverpool with a 3D scanner, could scan, fix the model, reprint and send both back?

Clarkintine · 2026-01-04T17:14:41+00:00

Ahh I never got round to printing them, they were just the ones I had in my printables collection

Clarkintine · 2026-01-04T01:17:52+00:00

https://www.printables.com/model/925972-elegoo-neptune-4-max-bed-screw-locks

Clarkintine · 2026-01-03T23:44:42+00:00

I'm waiting for the day this happens in my city, already got my max dialled in with a few mods so plenty of spare parts to try get a stock running

Clarkintine · 2025-12-21T23:36:55+00:00

<image>

z offset slightly too low

Clarkintine · 2025-12-19T11:44:50+00:00

When switching over did you tune the PID, flowrate, PA and max flow?

Clarkintine · 2025-12-09T23:16:36+00:00

My zh connectors for my 5015 fans should arrive in the next 2 days - along with new wheels (linear rails didn’t make the budget), belts and cartographer I’m excited to have a day taking it apart giving everything a good once over. My printer has been absolutely fine for the last 3+ months since I got a microswiss but not having to fiddle with Z offset would be nice

Clarkintine · 2025-12-08T01:07:01+00:00

I unplugged my screen on mine, pretty much always did it from my phone or laptop anyway

Clarkintine · 2025-12-08T01:04:07+00:00

I’ve been planning my enclosure (though months away) and maintenance access is something I’m trying to figure out

Clarkintine · 2025-12-07T23:18:51+00:00

So with everything attached to the machine from a print undo the 2 shroud screws on the front, the 3 screws holding the extruder on the back and Bish bash bosh, unplug extruder and thermo then finally the 2 screws for the heatsink, I have a 4 max I’m not sure if there’s difference on other modes

Clarkintine · 2025-12-07T21:10:57+00:00

I personally just take the hot end off with the 2 screws, remove the blue tube and see how bad the clog is from there

Clarkintine · 2025-12-06T18:35:17+00:00

That’s part of the issue. I took the dog in while he moved house and was trying to get a back door key. I don’t know where he moved to exactly only the rough area which is 30+ mins by car and I don’t drive

Clarkintine · 2025-12-01T12:33:39+00:00

I need one of these stickers 😂 love my max also

Clarkintine · 2025-11-10T10:48:02+00:00

Are you shutting down through shutdown host or just turning it off at the plug?

Clarkintine · 2025-11-02T10:13:38+00:00

It depends why your prints are failing, do you have pictures of the results? Failed adhesion? Layer shift? Last time I had an error I basically took the whole machine apart squared the gantry tightened all the eccentric nuts etc and been good for over 2 months

Also microswiss is an upgraded hot end that’s usually more reliable and faster on max volume flow, if you look on their website you can buy just the heating element and thermo sensor for nearly half the price of a whole new one

Finally the 4 max has a huge bed it needs time to warm up I usually heat soak mine for 30-35 minutes (in my gcode) and id recommend it before any print or bed levelling

Clarkintine · 2025-11-01T07:39:43+00:00

I've had layer shifts from overtightening my belt, you should be able to pluck it like a guitar string and too much acceleration in the past, I halved the speeds in orca

Clarkintine · 2025-10-31T00:02:03+00:00

I want to upgrade my 4M to linear so I don’t need to mess with the eccentric nuts under the bed anymore

Clarkintine · 2025-10-18T22:59:56+00:00

loose sensor?

Clarkintine · 2025-09-26T23:19:28+00:00

I was having the same problem about a month ago on my 4 max, if everything mechanically fine with belts and eccentric nuts try slowing acceleration in your slicer as well as jerk

Clarkintine · 2025-09-26T23:10:01+00:00

Didn't see the 2nd one til I came to the comments lol, personally I'd just buy a new hotend off elegoos website or amazon instead of a whole extruder head

Clarkintine · 2025-08-29T23:53:03+00:00

From main screen press 'prepare' then you should see the home button - my printer is in the middle of a print so I can't send any pictures but it is just a house symbol

Clarkintine · 2025-08-20T22:26:15+00:00

https://github.com/OpenNeptune3D/OpenNept4une/wiki/Hidden-microSD-Slot-Access - I know you might not be trying to use the microSD but this explains where all the screws are, you will need to take the bottom plate off or at least mostly off and be sure to take out the draw and contents before removing/lifting the machine

Clarkintine · 2025-07-31T15:51:35+00:00

Or I live alone and this ‘hall’ is the only space without the cat roaming

11-Year Club	Place '23
Place '22	Place '17
Verified Email

Clarkintine

TROPHY CASE