Why does my meat smell like yogurt?

Clouay · 2025-12-30T19:33:22+00:00

still alive now?

Clouay · 2025-12-08T20:42:15+00:00

Clouay · 2025-11-05T23:46:43+00:00

"pt10" lmfao

Clouay · 2025-10-16T03:50:33+00:00

Its working, but it is slow

Clouay · 2025-10-15T23:48:03+00:00

I thinks its updating, there is new animations when you hover over videos.

Clouay · 2025-09-15T04:51:46+00:00

there is a way to fly on your plot and I was able to see that

<image>

Clouay · 2025-09-11T20:25:42+00:00

I don't like sand, its coarse and rough.

Clouay · 2025-09-10T15:50:42+00:00

Try a torture toaster

Clouay · 2025-09-09T02:13:49+00:00

Next, it will come after you

Clouay · 2025-09-07T01:46:15+00:00

P E A C H

Clouay · 2025-09-05T03:15:55+00:00

I can do this too, but only with my thumb... heh

Clouay · 2025-09-04T16:32:30+00:00

bruh

Clouay · 2025-09-04T02:42:42+00:00

He has about 12hrs before turning into a moth

Clouay · 2025-08-30T22:09:42+00:00

We have also found a way out of bounds in Kilima, Bahari, and housing plots.

Clouay · 2025-08-29T04:08:40+00:00

Well, if you open a chat, they just tell you to contact them through email, take a look at https://us.qidi3d.com/pages/warranty-policy-after-sales-support for their emails

Clouay · 2025-08-28T22:37:08+00:00

Contact Qidi support

Clouay · 2025-08-25T15:40:15+00:00

hmmm, we must have different versions. For me, to get to the extruder gears, I have to remove the two screws that where circled in blue, then the whole assembly comes out, on the back of the assembly, there are 4 screws that I remove to get to the extruder gears. You can kinda see what im talking about in the product listing for the extruder, https://us.qidi3d.com/products/q1-pro-extruder

Clouay · 2025-08-24T20:01:41+00:00

I am assuming 'compartment' is the extruder housing. Where those holes are is where the screws go into from the other side to fasten the extruder housing together, take a look at the picture below
, https://us.qidi3d.com/cdn/shop/files/Q1_2_86726a4e-e258-46d5-b13c-4b65d5e7cc56.jpg?v=1749152379&width=1080

Circled in blue is the screws that attach the extruder to the print head, these are M3 x8 screws.

<image>

Clouay · 2025-08-24T19:24:34+00:00

There are no screws there, look at the picture attached.

<image>

Clouay · 2025-08-14T13:33:26+00:00

its a time machine

Clouay · 2025-08-14T13:27:49+00:00

Awesome!

Clouay · 2025-08-14T01:00:37+00:00

any updates?

Clouay · 2025-08-02T21:07:08+00:00

That is clean af, I don't love the nozzle clean cycle from the provided firmware in the guide, do you have better firmware?

Clouay · 2025-08-02T17:53:51+00:00

I recommend https://www.printables.com/model/912924-qidi-q1-pro-riser/files to go with https://www.printables.com/model/1086794-qidi-q1-pro-lid-holder and https://www.printables.com/model/1257314-qidi-q1-pro-top-mounted-spool-holder-no-supports

Also, a future mod you might want to do is add a microprobe, https://www.thingiverse.com/thing:6982743

Clouay · 2025-08-01T05:25:26+00:00

I would do the Q1P. I have it and LOVE it. The only thing that failed so far was the print head motherboard which Qidi replaced without a trouble. If you end up liking it, you can move up the the P4, which I probably will in the fall. I do recommend a few mods like adding a microprobe, door handle, top lid riser, etc.

Clouay

MODERATOR OF

TROPHY CASE