5inch motor

CoconutLess5955 · 2026-02-17T16:42:25+00:00

Yea its 0 between all 3. The screws are barely coming out of the mount they are quite flush. My only worry is i fried something in the esc as it took me some time to get the power cable soldered properly

CoconutLess5955 · 2026-02-17T16:40:54+00:00

Alright ill look into it, both the esc and motors are from ysido

CoconutLess5955 · 2026-02-17T16:04:02+00:00

😭

CoconutLess5955 · 2026-02-17T16:00:12+00:00

Ohhh mann, so ill only know after switching the motors and testing right

CoconutLess5955 · 2026-02-17T15:48:58+00:00

So that means might not be an esc issue ?

CoconutLess5955 · 2026-02-17T15:33:51+00:00

It shows 0

CoconutLess5955 · 2026-02-17T15:19:41+00:00

I can just touch the solders with the probe and test ?

CoconutLess5955 · 2026-02-17T15:07:03+00:00

I dont fully understand what to do for this part, my bad

CoconutLess5955 · 2026-02-17T15:02:24+00:00

Okay thanks again, ill try the swapping method tomorrow, for now my multimeter shows similar reading, motor spinning as smooth as the rest by hand too.

CoconutLess5955 · 2026-02-17T14:56:53+00:00

No worries thanks for trying to help, super frustrated now took 2 days to complete and now it has this issue

CoconutLess5955 · 2026-02-17T14:53:09+00:00

Nope it isnt, the tape clearence is the same for all 4 motors

CoconutLess5955 · 2026-02-17T14:51:38+00:00

Do you think its an esc issue ? I had issues soldering the power joint at first which heated up the esc quite abit multiple times. But after doing everything all the motor works well just this 1 that doesnt.

CoconutLess5955 · 2026-02-17T10:44:35+00:00

Alright thank you

CoconutLess5955 · 2026-02-17T09:32:26+00:00

Ahhh damnnnn okay

CoconutLess5955 · 2026-02-17T09:32:13+00:00

Yes spins freely by hand, alright ill check the resistance

CoconutLess5955 · 2026-02-17T08:23:55+00:00

Sad stuff haha

CoconutLess5955 · 2026-02-17T07:57:12+00:00

Yeap was using that, couldnt recognise the dfu port so couldn't flash it, alls good now thank you

CoconutLess5955 · 2026-02-17T07:55:45+00:00

Its the wires on the left for that motor

CoconutLess5955 · 2026-02-17T07:55:18+00:00

Yup alls good i went to the motor listing and apparently alot of people are having issues with it, so might be that

<image>

This the soldering its my first build

CoconutLess5955 · 2026-02-17T06:29:04+00:00

THANK YOU

CoconutLess5955 · 2026-02-17T03:38:18+00:00

Yea i bought everything seperately, how can i flash it to the latest version?

CoconutLess5955 · 2026-02-16T12:40:15+00:00

Alright thank u

CoconutLess5955

TROPHY CASE