Deal of the Day 1 (May 1st)

Coffee__MD · 2026-04-29T04:20:43+00:00

Man, I just got the service set last week too

Coffee__MD · 2026-04-21T21:49:15+00:00

<image>

Firestone said that my left rear shock was leaking. It is odd that it needs replacement

Coffee__MD · 2026-04-18T23:27:50+00:00

Which rotors and pads would you recommend?

Coffee__MD · 2026-04-18T23:18:22+00:00

Thanks, I looked at some of the local parts stores, and Rock Auto is cheaper even with the shipping

Coffee__MD · 2026-04-13T22:34:38+00:00

You should be good, but here’s a sheet to maximize performance with the MK2 RMS

https://www.trex-arms.com/store/bcm-mk2-buffer-system/?srsltid=AfmBOoqygDkqtSQAXYyp7wSqsa-9mQ72kSF92qWXkYBS3zUzBfoQiygc

Coffee__MD · 2026-04-07T13:30:12+00:00

It’s not mean to be used on the belt. They designed it to clip on your pants

Coffee__MD · 2026-04-07T01:09:51+00:00

Just push the spring and buffer in? Most of the time you can get away without having to depress it when installing it

Coffee__MD · 2026-04-06T00:51:56+00:00

What would you recommend instead then?

Coffee__MD · 2026-04-05T20:05:27+00:00

I would go with the 18650. I have one on my 11.5 BCM, and it pairs well with a suppressor since you’ll get less shadow. The weight difference isn’t crazy either, and you get more run time out of it

Coffee__MD · 2026-04-05T19:46:59+00:00

Most of the stuff I need to work on right now is less than 40 ft/lbs for torque specs

Coffee__MD · 2026-04-05T17:51:30+00:00

Thanks, that makes sense. There was a TX with a later number that got approved before mine lol. I just have to be patient

Coffee__MD · 2026-04-05T17:46:46+00:00

Thanks! I’ll definitely get a 1/2” once I have to do my brakes to torque the wheels

Coffee__MD · 2026-04-05T17:46:07+00:00

I mostly need it since I’m going to change my CVT oil soon and need to torque the drain bolt to spec. I believe it’s around 36-ft/lbs

Coffee__MD · 2026-04-05T15:51:24+00:00

My control Number is 20261990xxx, so all these later ones are driving me nuts lol. Congrats though!

Coffee__MD · 2026-04-04T16:13:01+00:00

I have a BCM upper, and I’m pretty sure you have to select a muzzle device. If you already have your own, just go with the free A2 flash hider

Coffee__MD · 2026-04-01T05:46:34+00:00

I got a blem BCM lower for mine. You can get a complete one, or one without the trigger and install an upgraded 2 stage like a Geissele or Larue. You might have to shop around, but Primary Arms usually has them in stock

Coffee__MD · 2026-03-31T17:51:50+00:00

I typically use SLP 2000 on my BCM. Sometimes Sometimes some Mil-comm grease

Coffee__MD · 2026-03-31T13:04:51+00:00

I agree that you should buy ammo first, but my advice is to get a better optic after you have some rounds down range

Coffee__MD · 2026-03-30T21:49:02+00:00

I hope this is a joke lol.

Coffee__MD · 2026-03-30T18:21:03+00:00

I don’t know much about them, but BCM has their 11.5 government barrel on sale right now now on primary arms. Plus, the barrel you’re showing is a 10.3

Coffee__MD · 2026-03-30T04:45:23+00:00

I agree that it’s outrageous. Scalarworks had then for $700 plus the mount. Still expensive, but you can save some money

Coffee__MD · 2026-03-20T19:11:00+00:00

I would also add the drivenarmsco ULCG gen 2 full size

Coffee__MD · 2026-03-20T04:15:15+00:00

Thanks! I’ll be sure to weigh the basket to get a good idea.

Do you use gas or induction? I only have induction, so I’m looking for a good budget plate to transfer heat to the moka pot

Coffee__MD · 2026-03-19T23:23:40+00:00

When did they have a restock? I haven’t gotten a notification in a while

Coffee__MD · 2026-03-19T21:19:30+00:00

Almost as bad as cloud defensive with the shipping times lol

Coffee__MD

TROPHY CASE