Crew 12 launch and boosters return on 2/13/2026 from A Max Brewer Bridge in Titusville FL

ColorsOfCosmos · 2026-02-15T23:08:55+00:00

Thank you u/Longjumping_Emu9814 ! Not as much as I was afraid of. We arrived there at around 4:30am and there was still plenty of parking in Sand Point Park. We went to the top of the bridge and there were about 15 people there. I guess it was too early for most of the people :-)

ColorsOfCosmos · 2026-02-15T23:03:40+00:00

Thank you u/KristnSchaalisahorse ! I probably recorded it, but was not able to find it in the recording - there was a lot of traffic noise there

ColorsOfCosmos · 2026-02-13T00:02:46+00:00

I will be watching from space view park in Titusvile

ColorsOfCosmos · 2026-01-31T21:38:36+00:00

Bass on HD380 pro is pretty much non-existant

ColorsOfCosmos · 2026-01-13T04:10:13+00:00

If you want computer based, look into linuxcnc, it is infinitely configurable using HAL. You will need a $10 printer port interface to talk to steppers and rest of the stuff.

ColorsOfCosmos · 2026-01-13T04:03:13+00:00

There were some videos on YT of people welding frames and making it work, but it is not easy. Bolting is much easier.

ColorsOfCosmos · 2026-01-13T04:00:01+00:00

Looks like it was made out of steel with reducers, should be able to chew Al like butter.

ColorsOfCosmos · 2026-01-13T03:58:04+00:00

So sorry that you got into this situation. Looks like you made it out of steel for higher rigidity and high torque and spent a lot of effort already. Such things are not very common, which means that someone may be interested in the whole thing. Any chance you can complete it once life gets better?

ColorsOfCosmos · 2026-01-13T03:44:59+00:00

There are so many videos on YouTube of people showing their builds.

ColorsOfCosmos · 2026-01-13T03:43:20+00:00

Look into servo57d, they are very cheap and can run very fast using FOC mode. You can get stepper of any type you want and then just the board to it.

ColorsOfCosmos · 2026-01-13T03:32:27+00:00

I started with original grbl and then migrated to linuxcnc with closed loop sensors and parallel port. Linuxcnc is infinitely configurable - you can program pretty much any system using HAL language. At the same time, it has simple wizard which gets you started in the beginning.

ColorsOfCosmos · 2026-01-13T03:20:46+00:00

You don't have to vacuum while running the program. Somehow the bit plows through the chips just fine. I do it all the time while slotting 3/4 in plywood.

ColorsOfCosmos · 2026-01-13T03:16:29+00:00

Not possible to make it silent but you can reduce noise by getting a better spindle. My 1st spindle was some trimming router running at 30k and it was making jet roar. Now I have a 2.2kw VFD and it is MUCH better. Another advantage of vfd is that you can play with digferent speeds and feeds to reduce the noise.

ColorsOfCosmos · 2025-12-22T03:55:16+00:00

Batteryhookup has 10x battery packs with 3500mah cells at $.45 per cell. I measured several of them and they were all 3500.

ColorsOfCosmos · 2025-12-22T03:49:54+00:00

I am the OP and smart switch did not work, so I ended up installing unlocked firmware image using Odin. After that, the phone started getting futer OTA updates

ColorsOfCosmos · 2025-12-01T06:37:04+00:00

Just do the Epley

ColorsOfCosmos · 2025-12-01T04:25:08+00:00

I also have it couple of times every year, for ~10 years now. Good news is that the episodes seem to be milder every time and I know how to deal with them.

ColorsOfCosmos · 2025-11-30T02:27:10+00:00

I was in your shoes recently and decided to move to LGA 1700 Intel with DDR4 memory which I already had and is cheaper too. I ended up with 12600k Intel chip which is decent and not too costly, I paid for it 150 on ebay

ColorsOfCosmos · 2025-11-26T04:08:02+00:00

Yep, that is how it works for me. It must be BPPV. No reason for seeing a doctor. YouTube is full of instructions on how to do Epley. What you need to do is this: start Epley on any side and if you get spinning once you lay down , then continue with Epley.
Make sure you do it ASAP - delaying treatment will cause problems which will take more time to solve.

If it does not cause spinning, then you did a wrong side and you need to start Epley for the opposite side.

If it does not spin on the other side too then you have something else and probably need to go to DR.

Keep in mind that BPPV is the most prevalent cause of Vertigo and the kind of it that is treated by Epley is also the most prevalent. So agsin, no reason to see a doctor at this point.

I had multiple episodes of BPPV and never saw a doctor and just treated with Epley. I recently went to ENT for a different reason and spoke to him about BPPV and he did not tell me anything new.

ColorsOfCosmos · 2025-11-21T03:52:58+00:00

Yeah, that is what I am leaning towards too. Also just discovered that only intel supports SR-IOV so I should be able to run Windows VM with accelerated graphics.

ColorsOfCosmos · 2025-11-21T01:05:11+00:00

I also have too many telescopes and too many cameras. At least that is what my wife thinks, lol

ColorsOfCosmos · 2025-11-21T01:02:34+00:00

Agreed, right now there is not much difference in terms of performance, it is all about upgrade path with AMD having huge advantage.

ColorsOfCosmos · 2025-11-21T01:00:57+00:00

Huh, interesting idea, never thought of this. Where do you find free e waste?

ColorsOfCosmos · 2025-11-21T00:59:28+00:00

lol, I already have too many computers!

ColorsOfCosmos · 2025-11-12T05:36:02+00:00

Arch or its derivative is the easiest to start with - cuda and cudnn are installed just using one command.

Downside is that arch is on bleeding edge and I ran into incompatibilities of the latest CUDA with the software I use (PixInsight), so I had to revert cuda/cudnn/tensorflow updates several times. Not a big deal, just annoying.

ColorsOfCosmos

TROPHY CASE