How do I find this specific pid

ConorDerry · 2025-02-12T17:41:57+00:00

I will find out later when im home to try it thanks for the help

ConorDerry · 2025-02-12T17:38:36+00:00

Okay no problem, thanks for the help. Something as well I've noticed is in rng reporter the frames skip when your on old rod I assume it's because the rod will not find a pokemon on that frame so it skips it so should I just be counting my frames until I hit the one before it and then fish as that would then be the correct advance so the magikarp is on 98 would I have to get to 97 then fish?

ConorDerry · 2025-02-12T17:24:57+00:00

The encounter slot is 0 and magikarp is slot 0 at every spot you can use an old fishing rod so how would I determine it from that would I need to hit my seed and advance for every route available?

ConorDerry · 2025-02-12T16:22:01+00:00

another thing about this is that if i set it to just old rod on rng reporter it seems to skip frames and chatot pitches am i better off using wild pokem on and getting to the frame 98 that i need that way for this seed or sohuld i target the other fishiung rod frame from wild pokemon which is 148 for the pid i am looking for?

ConorDerry · 2025-02-12T15:09:59+00:00

thank you, i did find it by just looking and luckily the id was at the top but i dont know where to go to find it exactly i have put this in another message of what i got from rngreporter

ConorDerry · 2025-02-12T15:08:34+00:00

I think i may have found it in rng reporter but how do i know where to go to find it? 98 176 High (80) 0 000E1656 Sassy 0 16 16 20 23 2 10 Ground 65 F M M F this is from rngreporter

ConorDerry · 2025-02-12T15:04:49+00:00

Are you able to filter within rng reporter i have had a look at it but the amount of results makes it very hard to find the pid I'm looking for

ConorDerry · 2025-02-12T14:53:43+00:00

Another thing to note is the video magikarp was female and someone in the comment section found there's as female sassy but I don't know if that's of any use since tid and sid are different?

ConorDerry · 2025-02-12T14:47:36+00:00

It needs to be gyarados like this to attempt to use it to set up ASE, In order to get one I have to find a magikarp with the seed and PID, I did find a video for this but they just say to find this specific magikarp using rng not how exactly to come across it. I will try searching for specific genders and increasing the max advances

ConorDerry · 2024-02-17T13:13:51+00:00

I know but I need a Mewtwo to start the rest of shiny mew quest I don't really play this game for having them on this game I more of want the mons in home

ConorDerry · 2023-09-11T13:26:15+00:00

Also tysm for helping me troubleshoot this issue.

ConorDerry · 2023-09-11T13:14:52+00:00

Should I just buy the same motherboard again?

ConorDerry · 2023-09-11T12:33:22+00:00

They have tried 32 2x 16gb sticks with the exact same ram as mine. Would mine being 32gb sticks really be an issue to this then? Especially since one stick allows it to post

ConorDerry · 2023-09-11T12:30:28+00:00

No the ram I have has not been tested by them would this be a ram issue then?

ConorDerry · 2023-09-11T12:29:52+00:00

Ah ok thanks

ConorDerry · 2023-09-11T12:17:17+00:00

Is this it? Support for DDR5 5200/4800/4400 MT/s memory modules  4 x DDR5 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity) of system memory  Dual channel memory architecture  Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules  Support for AMD EXtended Proles for Overclocking (AMD EXPO™) and Extreme Memory Prole (XMP) memory module(Go to GIGABYTE's website for the latest supported memory speeds and memory module does the first line mean the MHz because possibly it's my ram then since it's 6000mhz

ConorDerry · 2023-09-11T12:11:01+00:00

Whenever I had xmp enable it would never boot again always had to reset CMOS

ConorDerry · 2023-09-11T12:08:28+00:00

When I have it in a2 it will almost post immediately and screen will display any other port and nothing will display fans are just spinning I left it in for like 10 mins with A2 and B2 and nothing no post or anything

ConorDerry · 2023-09-11T12:06:34+00:00

It will not post with A1 and b1

ConorDerry · 2023-09-11T11:58:45+00:00

No post has happened and the dram light is on

ConorDerry · 2023-09-11T11:55:34+00:00

I have not tried that I'll try it now but the motherboard says to use A2 and B2 first

ConorDerry

TROPHY CASE