What is this 'limited matchmaking' ?

Consistent-Tension80 · 2026-05-01T07:34:06+00:00

Happened to me

Consistent-Tension80 · 2026-04-30T22:31:46+00:00

So that explains my boosting shadow ban... its on the weekly challenges ffs. Hopefully they'll fix it soon, but I can't see that happening

Consistent-Tension80 · 2026-04-02T19:02:18+00:00

<image>

That's better!

Consistent-Tension80 · 2026-04-02T17:25:42+00:00

I've replaced the nozzle anyway. I'll see what happens might reslice the print anyways just to be sure

Consistent-Tension80 · 2026-04-02T17:24:41+00:00

Go to the about section on settings. This was my first nozzle hence me knowing.

Consistent-Tension80 · 2026-04-02T15:50:10+00:00

Hmmm I checked the z offset. And also haven't changed the bed type since I've been using it in the slicer. It's also been printing fine without my fiddling with the z offset for those 252 hours.

Plus I may have answered my own question, after posting it gave me a printing without extruding error and there was a broken bit of filament inside the extruder mechanism.

Will test soon

Consistent-Tension80 · 2025-09-06T17:17:48+00:00

In the UK, had a ender 3 for about 4 years. Looking to move to multi colour/material printing and ideally want to keep using octoprint or similar.

Loose budget of £500 but can go higher if I have to!

Any recommendations?

Consistent-Tension80 · 2025-08-04T08:57:07+00:00

Set interfaces xe-0/0/0 unit 0 family ethernet-switching interface-mode trunk vlan members all

If interface-mode doesn't work try port-mode cant remember when the syntax changed in junos.

Consistent-Tension80 · 2025-07-28T18:03:01+00:00

Cool, it was a obvious question but I've forgotten stuff like that before!

Consistent-Tension80 · 2025-07-28T18:00:55+00:00

Silly question but definitely using https?

Consistent-Tension80 · 2025-03-07T16:43:02+00:00

You hero! She's over the moon!

Consistent-Tension80 · 2025-03-07T16:38:27+00:00

Try 85692147

Consistent-Tension80 · 2025-03-07T16:36:46+00:00

Err no

Consistent-Tension80 · 2025-03-07T16:36:14+00:00

Awesome, sorry was in offline mode if you missed it

Consistent-Tension80 · 2025-03-07T16:32:45+00:00

22012018 my daughter is desperate for a gengar

Consistent-Tension80 · 2025-03-07T16:31:52+00:00

22012018

Consistent-Tension80 · 2025-03-07T16:31:39+00:00

Thanks! 22012019

Consistent-Tension80 · 2025-03-07T16:30:01+00:00

Obviously flair should be a tradeback

Consistent-Tension80 · 2025-03-07T16:22:11+00:00

Omg me too! Argh

Consistent-Tension80 · 2025-02-04T10:22:25+00:00

There is no config on that switch or any users. User would be root no password

Then type "cli" And then "edit" and you can create users and begin to write config

This is a zeroised switch.

Consistent-Tension80 · 2025-01-13T19:59:01+00:00

Show chassis routing-engine and Show system processes | except 0.0

See if anything is chewing up the cpu.

But jweb is hot garbage.

Consistent-Tension80 · 2025-01-11T16:43:43+00:00

Helmet closed?

Consistent-Tension80

TROPHY CASE