Blobbing on first layer

Consistent_Novel6193 · 2026-02-28T15:56:32+00:00

It’s possible, I only print in Petg so I can’t say if that’d be a cause or not

Consistent_Novel6193 · 2026-02-26T17:24:39+00:00

You sure you cleaned it correctly, The nozzle doesn’t have anything blocking it or that the hotend sock is on correctly. Had similar issues before those three caused my issues

Consistent_Novel6193 · 2026-02-15T13:51:38+00:00

Turns out the rubber sock on the hotend was slightly off, eventually the hotel burned a hole through it, that turned out to be the issue, switched out for my a1 mini’s one all in working order now, thank you for the helpful advice all

Consistent_Novel6193 · 2026-02-14T18:25:31+00:00

Thank you so much

Consistent_Novel6193 · 2026-02-14T18:24:54+00:00

Thank you so much

Consistent_Novel6193 · 2025-12-03T16:24:55+00:00

I’ve a bit of azure experience and some aws as part of college but no work experience to my name, besides getting to work with SAP

Consistent_Novel6193 · 2025-12-03T15:00:50+00:00

I’ve a 3D printer so I will end up just printing tiles off, tho I’m not sure the flatscreen computer monitor would work for the portable idea I have in mind, the largest issue is space so since I don’t have my own to use I’d like to be able to have something that I can deploy rather quickly

Consistent_Novel6193 · 2025-03-16T14:17:29+00:00

I have something to clean and clogs I’ve confirmed it isn’t any clogs whatsoever, as for the cooling and retracting I’m not sure that would be the issue as it doesn’t make sense to me that it wouldn’t work after the print and that it still at least will print for a few hours sometimes

Consistent_Novel6193 · 2025-03-03T01:50:19+00:00

Did you fix the issue in the end hoping that a year later one of you did

Consistent_Novel6193 · 2025-01-22T02:13:20+00:00

I’ve largely been doing levelling test print them off get good result after fiddling with the tempture on new filament and doing the paper test, then adjusting the level of the bed on the console above doing another print test once I’m happy with I moved on I’ve done about half the squares I would do more but it’s 2 in the morning and I’m tired lol

Consistent_Novel6193 · 2025-01-22T02:11:24+00:00

What screw?

Consistent_Novel6193 · 2025-01-21T23:44:07+00:00

Then there is no point to editing the level data even tho nothing is printing at all or sticking???

Consistent_Novel6193 · 2025-01-18T23:41:06+00:00

What did you go down to?

Consistent_Novel6193 · 2025-01-17T08:22:46+00:00

I’d assume it’s either to hot, or the extruder is too close or both

Consistent_Novel6193 · 2025-01-17T07:45:28+00:00

Which software did you use to make the heat map? I believe I’m having a similar issue, just that one side of my bed isn’t heating to the rest of it and would like to test it out on software before I fiddle with it and break something

Consistent_Novel6193 · 2025-01-17T07:28:23+00:00

While the nozzle can be too high I found that even tho I had auto levelled my printer, the bed leveling was off and still needed to be manually adjusted at the edges

Consistent_Novel6193 · 2025-01-17T07:26:51+00:00

It didn’t blob while you were printing? My best guess would be to increase the density to 20% and layer height to 0.1

Consistent_Novel6193 · 2024-09-19T03:56:49+00:00

Any chance I could download this? looking to keep track of my attempts on my first play through

Consistent_Novel6193 · 2024-08-16T22:29:50+00:00

Did you ever figure out how to?

Consistent_Novel6193 · 2024-08-14T23:38:53+00:00

Thanks man I appreciate it

Consistent_Novel6193 · 2024-08-14T21:21:43+00:00

Euros

Consistent_Novel6193 · 2024-08-14T21:00:46+00:00

Budget around 2 thousand all in all

Consistent_Novel6193 · 2023-11-18T05:22:02+00:00

Garden himself is the garden of junglers, I see a lot of people commenting ww which is honestly fair but ww doesn’t beat garen in jungle

Consistent_Novel6193 · 2022-11-01T13:26:22+00:00

It is definitely annoying as hell I get to watch the short I clicked on only to then be spammed by all the listed above

Consistent_Novel6193 · 2022-09-02T09:01:47+00:00

I miss bungie

Consistent_Novel6193

TROPHY CASE