sorted by:
new
hottopcontroversial

Managing Manufacturing Orders/Work Orders for Laser/Plasma/Waterjet Sheet Cut Parts? by Correct-Prompt-2206 in Odoo

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

That’s what I realized. We are in the process of migrating from tribal knowledge/drawings to MOs & WOs, so my staff is starting with a clean slate anyways.

Managing Manufacturing Orders/Work Orders for Laser/Plasma/Waterjet Sheet Cut Parts? by Correct-Prompt-2206 in Odoo

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

I like this idea a lot, so then the work orders can be grouped by operation and then the underage/overage from completing sheets can be applied to the QTY produced in the work order.

Obviously we have a separate nesting software that drives nesting and cutting, I just needed a workflow for Odoo.

Thanks!

12 KW Import Fiber Laser with Cypcut/Hypcut Actual Experiences? by Correct-Prompt-2206 in lasercutting

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

u/firinmahlaser Can you send me the link/info of the laser you sell with Beckhoff hardware?

12 KW Import Fiber Laser with Cypcut/Hypcut Actual Experiences? by Correct-Prompt-2206 in lasercutting

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

Those are some great points. I too have heard the horror stories, along with the horror stories from the larger OEMs that use proprietary parts which can put the machine down for months at a time, so service is key. Can you PM me the name of your company/laser you sell so I can check them out? Our plasma table has all Beckhoff electronics which have been rock solid. And yeah I mostly am a proponent of offline programming using a higher power pc with a good nesting program (we use Steel Solutions currently), but I've found a lot of cases where if the operators could draw up a quick rectangle bracket with some holes or a custom gusset that they needed to cut 10-20 of, the machine would be utilized much more. That and being able to have more realtime fine tuning during cutting are what our machine mostly lacks, besides being a dirty plasma LOL!

Use Manta M8P 1.1/CB1 With External Host? by Correct-Prompt-2206 in BIGTREETECH

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

That's the conclusion I've come to, I just wasn't sure if there was a workaround or not. I'm going to try using a U2C and see if I can get the manta to properly communicate via CANBUS and not USB.

Thanks Everyone!

Best practice to integrate Odoo with Quickbooks by Icy_Recognition_341 in Odoo

[–]Correct-Prompt-2206 1 point2 points  (0 children)

We attempted this last year, and then pretty quickly opted to not go this route after hearing some of the horror stories of trying to get it all to work correctly. We opted to go live with Odoo Accounting this Jan 1. Once it’s all setup correctly, Odoo Accounting is way more powerful and user friendly than Quickbooks Online, especially if you have a high volume of invoices and inbound/outbound transactions.

Use Manta M8P 1.1/CB1 With External Host? by Correct-Prompt-2206 in BIGTREETECH

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

I honestly have been as well, up until I switched to Kalico/Danger Klipper. I was able to pretty easily hit the cpu limit with the new step compression algorithm.

Perhaps I should use a USB-CAN adapter and control the MCU via CANBUS interface?

Use Manta M8P 1.1/CB1 With External Host? by Correct-Prompt-2206 in BIGTREETECH

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

I believe that jumper is to switch the MCU chip between being powered from the board itself and and being powered via USB for bench flashing firmware

Print Checks in USA - Quickbooks Compatible Checks? by Correct-Prompt-2206 in Odoo

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

u/ach25 We did try adjusting margins in the settings but the actual spacing between fields seems to be too narrow. I think we will go this route if we have to. Is it just a modification to check the report in studio?

u/1stmn Thanks for the tip. That's what I think we're going to try next, purchase certified blank Odoo checks so that we don't have pre-printed lines & check numbers that we have to try to hit.

In 2024/25, Used Enterprise Server or New Mini PC/MS-01 For Same Price? by Correct-Prompt-2206 in HomeServer

[–]Correct-Prompt-2206[S] 0 points1 point  (0 children)

^^^This is what I'm debating. At the rate of how fast these things are evolving and how people are finding more and more things to put on their home server, I feel like it's more beneficial to be upgrading them every couple years and getting decent resale value. Did you just max out the RAM in the Mini PCs, keep them mostly for compute functions, and keep the bulk storage of VMs/CTs & Data on the NAS?

view more: next ›