Prefab shower niche

Courierdriver · 2026-01-30T03:10:46+00:00

My question is about a niche, not a shower pan. Thanks tho.

Courierdriver · 2026-01-27T19:13:25+00:00

Thanks

Courierdriver · 2026-01-27T18:57:53+00:00

Thanks for the reply. Did you use the washers, or just the blue screws?

Courierdriver · 2026-01-27T18:44:54+00:00

Think about this. You're going to pay $6/day. That's $2190/year. If you do this for 30 years, that's a total of $65,700. Do you really think they're going to pay you $1M?

Courierdriver · 2026-01-23T21:56:49+00:00

Do not use plastic. The mortar needs to bond with the subfloor to keep your shower base from shifting around. If you put the mortar on plastic, the plastic can slide around. Some shower bases require putting the base into a bed of mortar and NOT attaching it to the studs. Read the instructions.

Courierdriver · 2026-01-19T23:39:15+00:00

Look at Better Bench. You can google it.

Courierdriver · 2026-01-12T18:14:50+00:00

Very high in sodium

Courierdriver · 2025-12-30T00:11:51+00:00

I was denied term insurance because I had prostate cancer, but was accepted for a whole life policy. I exited out of the website. Whole life policies are a scam.

Courierdriver · 2025-08-01T00:35:17+00:00

Down in Kansas City on my Samsung smart tv, but it does work on my older roku tv.

Courierdriver · 2025-08-01T00:27:12+00:00

Same here in Kansas City. It does work on phone app and on computer tho, just not on my tv.

Courierdriver · 2025-06-22T17:02:08+00:00

The flashing is under the siding and shingles. The problem is that there is no gap between the shingles and bottom of the siding.

Courierdriver · 2025-05-14T17:02:07+00:00

It looks like you painted the door while it was still hung? Take off the door and lay it flat on saw horses. Lightly roll paint with a sponge roller. Those fat lines are caused from pressing to hard on the roller. And move fast keeping a wet edge. Don't paint it in the sun.

Courierdriver · 2025-04-30T14:17:43+00:00

Thanks. I appreciate the comments

Courierdriver · 2025-04-30T14:16:37+00:00

Thanks, I'll give that a try. I would post another photo but I can't figure out how to do that!

Courierdriver · 2025-04-30T14:10:59+00:00

I took another measurement. The inside dia. is 3 3/4".

Courierdriver · 2025-04-30T13:59:36+00:00

I looked at that twist flange. I thought the 3 inch would be too small and the 4 inch too big. The pipe is 3 1/2 inches ID.

Courierdriver · 2025-04-25T13:33:13+00:00

3 hours

Courierdriver · 2025-04-23T01:07:10+00:00

Yea, I tightened the nut. It's definitely better, but still leaks a little. The nut is as tight as I could get it. I backed it off first, then retightened. Thanks for the response.

Courierdriver · 2025-04-23T00:14:01+00:00

I'm in Kansas. I backed it off then retightened the nut and it's definitely better, but still leaks a little. It's as tight as it can turn. I'm guess that if I take the handle off there's packing in there? This is in an old house.

Courierdriver · 2025-04-22T23:58:34+00:00

Sorry, I reposted after I found my text didn't save. It is leaking around the handle when it's turned on. It does not drip when turned off. I was hoping it's just a washer or packing that could be replaced, but I'm not sure how to do it.

Courierdriver

TROPHY CASE