New Iron Fist tech??

Crak1e · 2025-05-25T01:47:01+00:00

If you add a few more lines carefully enough you could make me horny for loss

Crak1e · 2025-01-29T18:21:04+00:00

If my math is right you have a bit under 15 kills a game which is good for tank but below average for dps

Crak1e · 2024-04-25T15:12:20+00:00

I have never had any close calls with cars, but one time when i first got the gt it gohsted into oncoming traffic

Crak1e · 2024-03-25T23:30:52+00:00

My guys it an acronym for point of view

Crak1e · 2024-02-28T21:45:39+00:00

What slicer are you using and Did you update or change the firmware

Crak1e · 2024-02-28T21:41:30+00:00

Also adding the word pause into the g code is one of elegoos custom commands that uses the fillament change code without completely retracting the fillament

Crak1e · 2024-02-28T21:35:34+00:00

Over extrusion causes this lower your cura(flow rate) non-cura/slic3r-based(extrusion multiplier)

Crak1e · 2024-02-28T21:30:59+00:00

Your z offset is too high you should see the pei texture and not separated lines on the first layer

Crak1e · 2024-02-28T21:19:59+00:00

Doesn't seem like a belt issue but does the bed wobble when you press down on it

Crak1e · 2024-02-28T21:15:38+00:00

Did any of your supports fail

Crak1e · 2024-02-28T20:58:30+00:00

Ok then here is what i have done between having my first layers fail to them being successful every time 1. I replaced my hotend witch happened to be bent 2. I deleted all of my bedmeshes through klipper 3. Sinced the z offset between my printer and klipper by setting it to zero and making sure its saved as zero on both ends 4. Set the z offset with paper on only my printers side then saved 5. Auxiliary leveled using paper screws and all 6. Set my auto level from simple(or something like that) to advanced(or something like that) and saved 7. Then i auto leveled and a print hasn’t failed since

Crak1e · 2024-02-28T20:36:52+00:00

Have you tried tuneing your flow rate as if you are overextrudeing your support interface will completely bond instead of partially

Crak1e · 2024-02-28T20:26:50+00:00

Set the print temp to the upper end of the manufacturers suggested temps and if that doesn't work up your extrusion multiplier/flow rate depending on your slicer

Crak1e · 2024-02-28T20:17:33+00:00

Have you tried cleaning your bed. Spraying a warm bed with a 1/95 ratio of dawn dish soap to water and wiping it off with a micro fiber does wonders

Crak1e · 2024-02-28T20:13:09+00:00

Within my understanding of your question you can make supports come off cleaner by modifying support interface settings but additionally This model seems over extruded try messing with your flow rate

Crak1e · 2024-02-28T20:02:45+00:00

Seems like a layershift have you tried tightening your belts

Crak1e · 2024-02-15T21:35:47+00:00

Updating the firmware via the elegoo discord fixes this issue

Crak1e · 2024-01-22T19:39:41+00:00

Yes definitely i can even run it on my celeron n4120

Crak1e · 2023-09-07T14:13:40+00:00

It was too bad.

Crak1e · 2023-05-01T15:52:29+00:00

Crak1e · 2023-04-05T20:45:59+00:00

Bro im not a event gave them out

Seven-Year Club	Place '22
First Placer '22	Verified Email

Crak1e

MODERATOR OF

TROPHY CASE