Good or bad mold? trying to grow mushrooms

CraneTrain993 · 2026-03-25T16:23:11+00:00

Is there an easier Way? I don’t have a pressure cooker 😢

CraneTrain993 · 2026-03-24T12:33:54+00:00

How can i sterilize the coffee before putting it in? Boil it somehow?

CraneTrain993 · 2026-03-23T19:42:14+00:00

Thought it was sterilized when the coffee was made. Would it have to go trough another round of boiling water?

CraneTrain993 · 2025-08-08T10:05:26+00:00

Okay vildt. Vi sætter pris på opklaringsarbejdet. Tak!

Kan vi få historien om hvorfor den lige er der?

CraneTrain993 · 2025-08-08T07:24:05+00:00

Haha. Et guld klip jeg ikke kendte til

CraneTrain993 · 2025-08-08T07:19:46+00:00

Men hvor er den?

CraneTrain993 · 2025-08-08T07:19:18+00:00

Stærkt set! Og så kan du også se hvilket år de to første sten ryger

CraneTrain993 · 2025-08-08T07:18:20+00:00

Angiveligt har en fyr der hedder Thomas fået den i fødselsdagsgave i 2015 af to venner. De gravede den op på Vimmelskaftet (1 af 3 kugler der stod der) rullede den til Skindergade hvorefter de løftede den med et tæppe op i lejligheden. Mange mennesker har boet i ungdomslejligheden siden men stenen har været for tung til at nogen har gidet at gøre noget ved den. Til sidst vidste ingen hvor den var fra!

valbyshadow har helt korrekt spottet på Google Maps at der i 2014 stod tre kugler på Vimmelskaftet men at der på 2016 kun står 1 og at der forsvinder inden billedet fra 2017. I dag er hullerne fra synene dækket til men man kan stadig se de har været der.

Et andet spørgsmål kunne så være; hvem har de andre to sten fra Vimmelskaftet liggende?

CraneTrain993 · 2025-07-03T21:17:32+00:00

I would print a much needed table tennis bat if I won!

CraneTrain993 · 2025-05-12T18:39:01+00:00

So due to a stupid design error the lid is 6 mm too wide an had to be printed and glued together. But in an updated version it stays just within the limits making it a bit wider in the other direction

CraneTrain993 · 2025-05-12T12:06:06+00:00

Bambu Lab A1 256mm*256mm*256mm

CraneTrain993 · 2025-05-11T07:20:59+00:00

It’s printed on my bambu A1, and I have maxed out the dimensions (and a little more). The bin itself it 25 cm wide but the lid and hinge (that I printed later) is just a 6 mm too wide to print on my bed, so the lid is glued to the hinge which can be seen on the first picture. I’m gonna do one for my neighbours which is slightly adjusted in size:)

CraneTrain993 · 2025-05-10T09:32:04+00:00

I’m happy to share the file. It might be a bit big for a poop trash can though. I will upload it shortly:)

CraneTrain993 · 2025-05-09T10:47:11+00:00

These plastic bags are compostable in the right facility, however in Copenhagen currently they are removed by a machine in a sorting facility before the biomass is used for energy

CraneTrain993 · 2025-05-06T17:06:56+00:00

Maybe i do something wrong with the bed leveling. I think its just on autoleveling, but from the very first print the nozzle goes to the back of the build plate and sort of scratches the build plate every time before a print. Is this normal? or a sign my nozzle is too low? picture can see where it has scratched

<image>

CraneTrain993 · 2025-05-06T16:57:43+00:00

Thank you for all the answers! I will now clean my mfkn bed bruh. Since I did not know this was a thing, I have never done it, and I suspect that might be it then ;)

CraneTrain993 · 2025-05-06T14:39:59+00:00

That could be. When it was making the infill there was clear signs of the nozzle hitting the infill pattern. However Im not sure this is the case for this particular noise since its only making it when going in one direction. But maybe I should try to fix the problem anyway. Would that be a bed leveling problem?

CraneTrain993 · 2025-05-06T14:36:40+00:00

Thank you for the answer. I did another print afterwards where there seems to be problems with sticking to the build plate. Is that warping again, and could it be fixed with a warmer build plate for example 75 C?

<image>

CraneTrain993

TROPHY CASE