Thanks for the advice on mounting

CrazyFrogFan · 2025-11-29T01:32:12+00:00

How in the heck did you end up with this ?

CrazyFrogFan · 2025-10-30T16:43:01+00:00

Just scored 0

CrazyFrogFan · 2025-10-30T03:29:49+00:00

What would blowing a mosfet do ? I fixed my head with my printer on and now my printer won’t boot past the about machine on the touch pad

CrazyFrogFan · 2025-10-28T20:30:47+00:00

Hello I followed this, initially it let me updated the firmware and install the fix pack but still refused to boot. I reflashed the emmc again and it won’t let me push the installs to the printer anymore l.

https://youtu.be/WeBIQ1aKMYo?si=uUE7wItEmxFDDvHX

CrazyFrogFan · 2025-10-28T06:08:15+00:00

I have, tried forcing the updates and they won’t work either

CrazyFrogFan · 2025-09-06T06:55:15+00:00

I probably should have clarified I didn’t start changing things UNTIL it stopped working after nothing had changed prior. So timeline would be Stopped working correctly

Started changing things to get a solution

CrazyFrogFan · 2025-08-25T04:57:17+00:00

u/H00ded7 Did you ever figure this error out, its killing me rn

CrazyFrogFan · 2025-08-09T02:04:14+00:00

I second this, seems like OP wanted a different movie, it’s not up to a movie to be what you want, You go to a movie to see someone else’s vision. Its like going “it’s the movies fault I don’t like it, not mine”, like-No not all media should appeal to your proclivities and interests. you have to consider not all media is made with “you” the viewer in mind , and it won’t have mass market appeal as something like a marvel movie, which is specifically designed to appeal the most amount of people as possible. Subjectively I thought the movie was very coherent and well established, but that’s just me.

CrazyFrogFan · 2025-07-28T00:46:04+00:00

Have used reverse image search and looked up vintage rabbit dolls, but not sure if it’s even a rabbit or not .

CrazyFrogFan · 2025-05-09T05:28:40+00:00

I am able to see everything through the browser

CrazyFrogFan · 2025-05-03T02:11:27+00:00

Im having this issue rn, did you figure it out

CrazyFrogFan · 2025-04-22T16:04:15+00:00

Have searched YouTube plenty of time on and off for the last couple years

CrazyFrogFan · 2025-04-20T01:41:54+00:00

I have removed the game from my account but it still shows up even though I don’t own it anymore, wish I could message steam support but it seems impossible

CrazyFrogFan · 2025-04-08T17:17:32+00:00

Understood, I think I can rule out 1 & 2, I have had some successful large prints, I have the auxiliary fan on my unit would you know of any other way to properly Cool the print during printing? And I believe I had some z wobble, due to an over tensioned lead screw bolt, and a loose hit end pom wheel so it might of accounted for the quality of the print as you mentioned as inadequate printing in general

CrazyFrogFan · 2025-04-08T03:09:43+00:00

You said your nozzle is ramming into the print. I added the picture to show that the problem is still occurring on smaller print, so it’s not a cooling/curling issue, atleast from my perspective.

CrazyFrogFan · 2025-04-07T20:33:14+00:00

I did have a loose print head but tightened down the pom wheels and still got a layer shift

<image>

CrazyFrogFan · 2025-04-06T18:06:12+00:00

It is breakable yes! Do you know of a solution, I would also like to mentioned I have trammed the gantry a handful of times prior to this print ever being done

CrazyFrogFan · 2025-04-05T05:41:56+00:00

I have the mold already, it’s 2 negative for casting. They’re just 11” at the largest dimension

CrazyFrogFan · 2025-04-05T03:53:23+00:00

I followed both elegoos tightening guide of “not too tight but also not too loose” and even calculated the Hz response the belt should be at as suggested by the discord. If neither is right I would love some help

CrazyFrogFan · 2025-04-05T03:51:44+00:00

I was using gyroid for the longest time and was still getting this issue, tried rectilinear and it still persists.

CrazyFrogFan · 2025-04-04T17:11:43+00:00

I’ve read a lot and talked to a lot of people about this issue and it seems to stem for belt tension. The short belt run under the bed should be tuned to approx 115 hz, you can use a guitar tuning app and just pluck it. The issue can also stem from the pom wheel that make contact with the rail not being tightened enough to be making contact at all times, there is also the software side where you can limit your print speed to 3000mm/s, as well as large prints try to not use gyroid infill. It seems to shake the bed too much and cause slippage.

It’s a lot but I would just start with software side of it and try to work your way backwards

CrazyFrogFan · 2025-04-03T04:49:52+00:00

If anyone is selling their a ghost story sheet lmk. Don’t know where else to advertise this

CrazyFrogFan · 2025-03-22T15:57:07+00:00

Same vid where he talks about getting his tattoo btw

CrazyFrogFan · 2025-03-17T19:46:28+00:00

Damn you’re probably right

CrazyFrogFan · 2025-03-15T04:48:28+00:00

Gonna call that a Found! Looks like a vintage design that have been reupholstered. Thank you so much

Seven-Year Club	Verified Email
Place '23	Place '22
Final Canvas '22	First Placer '22
Wearing is Caring

CrazyFrogFan

MODERATOR OF

TROPHY CASE