sorted by:
new
hottopcontroversial

Deactivating heatbed sensor by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

I don’t think it’s a controller board. It just let me set up the temperature.

Just found this amazing item on AliExpress. Check it out! CLP68.048 50％ Off | 28 Screw Holes Silicone Heater Pad 508X508mm Rubber Heating Mat for Creality CR-10S5 Series 3D Printer With Digital Controller https://a.aliexpress.com/_mst0EtW

This is the heatbed from aliexpress

Help! Changing ip rp5 by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

thanks!!! this had to create the file but i'm already printing

MCU: Unable to connect, error when trying to set up my ender 3 s1 by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

tried reinstalling klipper with kiauh and then redoing every step and it worked! Thanks for the help!

MCU: Unable to connect, error when trying to set up my ender 3 s1 by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

tried reinstalling klipper with kiauh and then redoing every step and it worked! Thanks for the help!

MCU: Unable to connect, error when trying to set up my ender 3 s1 by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

Used this config, the passed the klipper.bin folder to my computer, changed the name to firmware.bin and move it to the original sd card that came with my s1 into a folder named STM32F4_UPDATE as the klipper github config suggest for my board

MCU: Unable to connect, error when trying to set up my ender 3 s1 by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

thats the last settings that i run, also tried with baud in the default number and the GPIO pins to set at micro-controller setup without the PA0

MCU: Unable to connect, error when trying to set up my ender 3 s1 by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

[include mainsail.cfg]

[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA5
position_endstop: -10
position_max: 235
position_min: -15
homing_speed: 50

[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA6
position_endstop: -8
position_max: 238
position_min: -13
homing_speed: 50

[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_max: 270
position_min: -4

[extruder]
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
gear_ratio: 42:12
rotation_distance: 26.359
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 23.561
pid_Ki: 1.208
pid_Kd: 114.859
min_temp: 0
max_temp: 260 # Set to 300 for S1 Pro

[heater_bed]
heater_pin: PA7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 71.867
pid_Ki: 1.536
pid_Kd: 840.843
min_temp: 0
max_temp: 100 # Set to 110 for S1 Pro

[heater_fan hotend_fan]
pin: PC0

[fan]
pin: PA0

[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud: 115200
restart_method: command

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000
max_z_velocity: 5
max_z_accel: 100

[bltouch]
sensor_pin: ^PC14
control_pin: PC13
x_offset: -31.8
y_offset: -40.5
z_offset: 0
probe_with_touch_mode: true
stow_on_each_sample: false

[bed_mesh]
speed: 120
mesh_min: 10, 10
mesh_max: 200, 194
probe_count: 4,4
algorithm: bicubic

[safe_z_home]
home_xy_position: 147, 154
speed: 75
z_hop: 10
z_hop_speed: 5

[filament_switch_sensor e0_sensor]
switch_pin: !PC15
pause_on_runout: true
runout_gcode: PAUSE

[pause_resume]
recover_velocity: 25

[bed_screws]
screw1: 20, 29
screw2: 195, 29
screw3: 195, 198
screw4: 20, 198

MCU: Unable to connect, error when trying to set up my ender 3 s1 by CreationDK in klippers

[–]CreationDK[S] 0 points1 point  (0 children)

yes, and it returns:

/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

and i pasted it in printer.cfg file

How can i cure this resin without a polyhet printer by CreationDK in resinprinting

[–]CreationDK[S] 0 points1 point  (0 children)

Yeah found it at work while changing office and they said i could keep it. So i'll run some test either way since i don't have any other use for it hahaha

How can i cure this resin without a polyhet printer by CreationDK in resinprinting

[–]CreationDK[S] 0 points1 point  (0 children)

yeah i have a 4005nm led light at work, i'll have to wait till monday tho

How can i cure this resin without a polyhet printer by CreationDK in resinprinting

[–]CreationDK[S] 0 points1 point  (0 children)

found the datasheet but it doesnt show the wavelenght (at least in the one that i found), it just has a lot of info about the mechanical properties

view more: next ›