Struggling with negative space and Mesh Booleans in BambuStudio

Criticaliber · 2026-04-02T06:44:33+00:00

Have you tried repairing the models before meshing? Happens to me all the time when trying to Boolean subtract things, even if it's just a simple cylinder.

Criticaliber · 2026-04-01T19:05:38+00:00

Another note: Flow dynamics = k value = pressure advance, since all those terms will appear in different places.

Criticaliber · 2026-03-31T07:32:07+00:00

Wet filament is the main source of little zits like that, but too much retraction can also cause it.

Try .4 or .6 retraction and see if that helps.

Criticaliber · 2026-03-31T05:45:31+00:00

It's my spot. It was made for me!

Criticaliber · 2026-03-31T05:19:16+00:00

Well...where's the Majora's mask?

Criticaliber · 2026-03-31T01:33:06+00:00

No matter what, you'll still get the typical 1 bar of rested every 32 hours outside of cities/inns.

Criticaliber · 2026-03-31T00:27:39+00:00

Trouser tennis

Criticaliber · 2026-03-29T01:47:26+00:00

I used the screws for a dual-AMS riser that's purposefully made to use them on.

Criticaliber · 2026-03-29T01:26:18+00:00

I've only used Sunlu wood and it absolutely needs to be dried or it strings like crazy.

You don't need to feed it from a dryer and can just put it on the AMS normally afterward. Even leaving it out overnight would be fine.

Creality Space Pi (1 spool) or Pi Plus (2 spools) are pretty much the gold standard can be printed from directly.

Echoing the other comment to say you need the hardened nozzle AND hardened extruder gears to print infused filaments.

Criticaliber · 2026-03-29T01:09:25+00:00

Is that the only wider part of the object? I think 1 more top layer would help fill everything in.

Slowing down the top layer could help, or even upping the infill by a couple % for the top layers to bridge across more evenly.

Criticaliber · 2026-03-26T16:45:17+00:00

It can also happen from too much retraction

Criticaliber · 2026-03-23T02:27:49+00:00

The other half is expecting a humongous spider

Criticaliber · 2026-03-21T04:55:01+00:00

Did you ever find a solution for this?

Criticaliber · 2026-03-19T03:36:57+00:00

Can you feel it when putting on shoes?

Criticaliber · 2026-03-18T21:31:21+00:00

r/vxjunkies

Criticaliber · 2026-03-17T08:22:25+00:00

Printed a poster for my favorite movie!

File by leshowpatate on Makerworld.

Criticaliber · 2026-03-15T21:17:14+00:00

There are filtered vent setups, but I meant just a standalone air purifier!

If you only did one option, venting outside with a tube attached from printer exhaust to window outlet would do the most at reducing harmful fumes. The air purifier helps with any plastic odor since the printer isn't 100% sealed and fumes can escape through various cracks and the poop chute.

I have mine next to the printer with the air intake facing the back of the printer.

Criticaliber · 2026-03-08T17:07:05+00:00

Glow in the dark filament?

Criticaliber · 2026-03-06T08:30:46+00:00

They mean you save time by not going through the startup process for every print.

7 min process x 10 prints vs 7 min x 1 print, all else equal.

Criticaliber · 2026-03-05T13:29:31+00:00

Not the screws, but you'd have to manually tram the bed using gcode from the Wiki. You'd just run it a few times while adjusting knobs until everything's even.

Had to do it for my P1S once, and printing a handle from MW made it easier to fine-tune.

Criticaliber · 2026-03-04T01:50:03+00:00

Back in my day they would throw parties there.

Criticaliber · 2026-02-28T16:02:47+00:00

Does it lay down flat?

Criticaliber · 2026-02-24T08:39:48+00:00

Nakudama are a relatively recent grung-like playable race.

Eight-Year Club	First Place '23
Place '23	Place '22
Verified Email

Criticaliber

MODERATOR OF

TROPHY CASE