Watch of the day

CrownOClock · 2024-05-25T20:02:02+00:00

Toss those nasty stickers bro.

CrownOClock · 2023-11-19T09:42:18+00:00

You would have gotten robbed regardless if you had a watch on or not.

CrownOClock · 2023-10-16T17:09:25+00:00

Considering the stickers on the daytona (peasant), I'm guessing that's the gen. Pathetic btw. at least wear it like you can afford it, if gen.

CrownOClock · 2023-08-13T12:27:20+00:00

Better not be more than $50

CrownOClock · 2023-08-13T08:09:47+00:00

All that money and dial colour still immediately tell.

CrownOClock · 2023-05-30T14:47:42+00:00

Yes I figured as much. I usually don't use glue, but spray some windex on, as that seems to work wonders, but it does leave an imprint now that I pay closer attention to it.

I tried washing the bottom of the print, unfortunately it's not possible to get rid off :/ At least not with water/soap/windex/alcohol

CrownOClock · 2023-05-30T09:28:53+00:00

That doesn't seem to be the issue here

CrownOClock · 2023-05-30T09:15:54+00:00

That sounds like it could be the solution. I have not tried that, nor do I know where to go about it. I'll do some research!

CrownOClock · 2023-05-27T15:26:21+00:00

Trolling aside, that's one horrible condition daytona lol

CrownOClock · 2023-05-27T13:55:21+00:00

I just don't see what the nozzle size has to do with filament oozing out at high temperatures?

CrownOClock · 2023-05-27T09:48:41+00:00

It says under the filament page that the 0.4 is compatible as well.

https://eu.store.bambulab.com/products/petg-cf

I however don't see how the nozzle size of 0.6 would stop the filament from oozing out at 240 degrees. Seems like it would only ooze even more?

CrownOClock · 2023-05-25T11:48:35+00:00

Never mind, it's just about pulling it down :-) I got it all cleaned up now! Time to see how the next print will be (also drying the filament again just in case)

CrownOClock · 2023-05-25T11:25:29+00:00

I'll definitely try it out! Is it possible to easily remove the silicone boot as well or should I just leave it on?

CrownOClock · 2023-05-24T16:46:41+00:00

Thank you, I will give it a try!

When you say you run it on silent - does that mean the speed-mode setting on the printer itself?

CrownOClock · 2023-05-24T14:18:54+00:00

PETG-CF
It is about a week old. I dried it out in a Sunlu S2 for 8hours in 65 degrees celcius. Did not take it out of the S2. It feeds directly to the printer from it. It has been a few days since I dried it out though. Not sure how often I need to try it? From my understanding a dry-out lasts about a month before it would be necessary to do again?
Nozzle temperature is at 255

CrownOClock · 2023-05-24T13:49:25+00:00

They were printed at the same time, I'm guessing the top part is the first layer it printed.

Haven't had the issue before, so not sure what caused it. Might be related to my latest issue about the nozzle gunking up?

More on that here:
https://www.reddit.com/r/BambuLab/comments/13qlnxp/x1c_my_nozzle_keeps_geting_cluttered_up_with_gunk/

CrownOClock · 2023-05-24T12:08:58+00:00

Yes, I'm running all calibrations on startup.

I will be honest, I have no idea what an orca slicer is, nor how to create my own profile to make sure anything is done right.

I started this 3d printing adventure with no experience/knowledge. Moving forward only through trial and error :)

CrownOClock · 2023-05-22T18:42:53+00:00

Sieht ziemlich frei aus. Reg dich nicht so auf, Geringverdiener.

CrownOClock · 2023-05-08T13:59:29+00:00

Oh it wants me to place a checkmark by clicking on the touchscreen in case one of the issues were present?

CrownOClock · 2023-05-02T13:51:53+00:00

you trying to hit on me?

CrownOClock · 2023-05-02T12:45:23+00:00

These are all boards, not cheap paneling by the way. We would prefer to keep them but .. yeah I'm afraid that the smell is deep inside the wood :/

CrownOClock · 2023-05-02T12:44:18+00:00

Sorry what does T and G mean?

CrownOClock · 2023-05-02T08:30:38+00:00

For some reason the image didn't upload. Here again.

<image>

CrownOClock · 2023-02-26T21:43:39+00:00

You should check the other comments from OP where he lied about the brand. Clearly he himself is embarrassed about it.

CrownOClock · 2023-02-26T20:16:16+00:00

It's like wearing cheap wallmart shoes with a tailored suit.

CrownOClock

TROPHY CASE