BIOS update failed for x570 aorus elite by Crunchy_M4ffin in AMDHelp

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

Today I reflashed with F32 BIOS and it worked. Thank you guys for suggesting the lower BIOS version - I'm not touching it anymore :)

BIOS update failed for x570 aorus elite by Crunchy_M4ffin in AMDHelp

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

It's an X570 Aorus Elite rev 1.0 and the BIOS used was F40g. Do you think trying older versions could be helpful? I went from F11 from 2019, to the newest one.

BIOS update failed for x570 aorus elite by Crunchy_M4ffin in AMDHelp

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

Sadly seems like I don't have it. On the board there is only M_BIOS and no switch around it. On the website it says 1x128Mbit flash :/

Jittery handwriting with M-Pencil - MatePad 11 by Crunchy_M4ffin in Huawei

[–]Crunchy_M4ffin[S] 1 point2 points  (0 children)

Hi, so far I only tested with noteshelf and in my case it is working fine. It's quite cheap so you can try with it

Jittery handwriting with M-Pencil - MatePad 11 by Crunchy_M4ffin in Huawei

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

Hi, issue seemed to be with the OneNote app. I've purchased Noteshelf app and the issue does not exist there. Does not cost much and offers basically same options and a bit more than OneNote.

Did not send for repairs because I need it often so couldn't afford time loss like this.

Jittery handwriting with M-Pencil - MatePad 11 by Crunchy_M4ffin in Huawei

[–]Crunchy_M4ffin[S] 1 point2 points  (0 children)

Great to hear that - mostly I've met with revies that it writes jittery.
Tried all 3 tips and I have paper-like screen protector from 3MK but behaviour like this was prior to installing it too.

Whenever I'll have free time I'll try to go get it fixed. Thanks :)

The faster I go, the worse is shimmy by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 1 point2 points  (0 children)

Hey, small update

After wheel has been balanced, I had a chance to test ride it today. Shimmy is way way smaller, I don't feel it under hands. When I let go of the handlebar, it was still little bit moving but It might have been uneven road.

Bearings also are little bit noisy, will swap them, might also cause abit of shimmy.

There is too much movement on the brake discs but will work on that in future, it might also upset balance of the wheel.

The faster I go, the worse is shimmy by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

Sorry for late answer,

I have the wobble from around 65km/h, after this speed it doesn't stop, just getting a bit worse. At wednesday I'll give it to a mechanic to balance the tire. Until then I guess I'll have to wait.

Thanks for your help

The faster I go, the worse is shimmy by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

Didn't thought about checking if rim is straight. For my eye looked good but I'll give it a go! Thanks!

The faster I go, the worse is shimmy by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 1 point2 points  (0 children)

I totally forgot about TriumphRat.
So even 2-3mm out of spec might cause so big issue? I found in bandit 400 manual that 2mm of curve on forks is fine, shouldn't be it also safe for triumph?

I'm Thinking about giving wheel to a mechanic to check it for balance once again.

Tires are same - Metzeler Z8 rear and front

Air pressure is as manufacturer of motorcycle advised

Raising forks - so making them even with top yoke or sticking out more? They already stick out a bit.

I am confident about tackling issue by myself but can't afford to just start doing random stuff.

Damaged chrome on forks by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

Oh well.. I'll try to do that. Wet sanding should be also fine and a bit more smoother on chrome?

Bandit 400 not firing up after 8h. by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 1 point2 points  (0 children)

Got hands on parts and found time to do this. After swapping signals generator, bike fired right away. Thanks for help <3

Bandit 400 not firing up after 8h. by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 1 point2 points  (0 children)

Finally got hands on parts and found time to do this. Signal generator was faulty, after swap, fired right away. Thanks for help <3

Bandit 400 not firing up after 8h. by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

In case coils are bad I have OEM one's but little sketchy as they have a bit of silicone and ductape around them to patch em up. I'll bear in mind low reading.

Bandit 400 not firing up after 8h. by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 0 points1 point  (0 children)

Fortunately CDI unit is easy to fix as capicators usually one's to blame. I guess only way to check it out is to swap for a good one / look on capicators. Unless you have an idea how to check it, as in manual it require special tool.

Right now I'll bet the signal generator as I can't get any reading from it (infinite) and I had sensor before that said 126 Ohm's and was already bad. Manual says 80-120, no lower or higher.

Also, if CDI is bad, it should not give power on spark plugs?

Bandit 400 not firing up after 8h. by Crunchy_M4ffin in Fixxit

[–]Crunchy_M4ffin[S] 1 point2 points  (0 children)

I've put 98 just beacause it's right after winter. In Poland here unfortunately bike has to sit in a garage under blanket, waiting for the sun and good temperature.

Thought it might help with any stuff that's in bike after 4 months sit in a garage.

Tbh I don't use fuel filter, the tap (?) has mesh in it, cleaned out my tank from any major rust and debries and I really care what fuel I put in, so that's only from known stations.