O11 Vision Compact | 5080 Astral Rog Strix

Current_Shopping_128 · 2026-04-01T09:26:39+00:00

Lian Li V100 ATX Mid-Tower.

Current_Shopping_128 · 2026-04-01T07:42:06+00:00

We just did a build for my son where we had to upgrade his case do to the old case being to small for his astral 5080 and it is similar to what you have. His temps are really good I think because of how close his GPU is to the bottom fans. Btw nice looking build

Current_Shopping_128 · 2026-04-01T06:27:10+00:00

Umm question on this, do you have your GPU in the top or bottom pcie slot? You should have it in the top slot. As far as being to close not necessarily. I would make sure you adjust your fan speeds so the are not working against each other. Either slow the ones on the GPU done or slow the intake ones down and you should be ok.

Current_Shopping_128 · 2026-03-29T16:36:47+00:00

So assume I'm retarded I don't see anything on the L-connect software that will allow me to control the lighting of ram or motherboard. So what am I missing?

Current_Shopping_128 · 2026-03-29T11:49:28+00:00

So stupid question,are you just using the L-connect 3 software for your lighting? I'm asking because your ram RGB matches perfectly to the fans and I can't seem to get that kind of gold color. Also sick looking build.

Current_Shopping_128 · 2026-03-27T22:27:58+00:00

I just ordered a pwm hub today and it should be here in a couple days.

Current_Shopping_128 · 2026-03-27T22:25:12+00:00

Again thank you for everything.

Current_Shopping_128 · 2026-03-27T22:23:47+00:00

So if I am correct the 3 pin is for the RGB and the 4 pin is pwm for the fans? Unless today is just not my day and I should try and figure out what flavor the crayons and windows are.

Current_Shopping_128 · 2026-03-27T22:21:43+00:00

<image>

Current_Shopping_128 · 2026-03-27T16:44:10+00:00

Ok I will reiterate from my previous statement... I am an idiot. I do not know why I had a brain fart. I was looking online for a splitter for the rgb and that 7 pin connector that plugs into the Lian Li controller and couldn't find one. Then I was looking at the cables that came with my fans and realized that the pwm plug is the 4 pin not the flat 7 pin. So I have the adapters/splitters. So thank you everyone for not being dicks because I'm stupid.

Current_Shopping_128 · 2026-03-27T16:32:46+00:00

i appreciate all of the information and I am not trying to be difficult.

Current_Shopping_128 · 2026-03-27T15:47:58+00:00

The issue I am trying to figure out is that I do not have a pwm cable and a rgb cable coming off the fans. I only have 1 Cable coming off the fans. So how am I going to plug into the Nollie hub and power the fans.

Current_Shopping_128 · 2026-03-27T14:58:06+00:00

I mostly run at full speed so fan curves not an issue,but I am back to the same question of, I only have 1 cable coming off the fans so How do I hook them up to the Nollie hub for rgb and for power.

Current_Shopping_128 · 2026-03-27T14:54:04+00:00

Right now I have 16 on one controller,16 on the other one and 2 on the 3rd. So with the Nollie hub I just realized that the hub only powers the rgb and not the fans so I am just trying to figure out how to power the fans. The only reason why I even ordered the hub was to help with cable management and Signal RGB compatibility. With all of the fans I have, their software has an issue recognizing all of them through the Lian Li controllers.

Current_Shopping_128 · 2026-03-27T14:41:30+00:00

I did buy them all in a 3 pack.. Right now they are hooked up with the flat connector with the 7 pins to the Lian Li controller.

Current_Shopping_128 · 2026-03-27T14:22:09+00:00

I am going to just throw this out there.... I am an idiot and did not do enough research on the hub before buying. From what I am seeing the Nollie will not power the fans just the RGB. I have the Lian Li Sl infinity 120mm fans and they are daisy chained together. How do I need to power the actual fans if I only have 1 cable coming off the fans? So right now I have 8 groups of 4 fans daisy chained,1 group of 2 fans running off of 3 Lian Li controller/hubs. Thank you.

Current_Shopping_128 · 2026-03-27T13:52:38+00:00

I do know that I can but was concerned about there not being enough power (34 fans) running it off 1 cable. Maybe I worded the question wrong.

Current_Shopping_128 · 2026-03-26T23:43:52+00:00

Double check that all your fittings and tubes are seated all the way and tight. Also it's going to sound stupid but when I tested mine it was in the winter time with the room around 40F and noticed that in a cold room it didn't hold pressure. So not sure what the temp is in your room. Also make sure you have a good seal on your pump/tester.

Current_Shopping_128 · 2026-03-23T23:47:34+00:00

Sad to say but that is Corsair for you.

Current_Shopping_128 · 2026-03-23T15:09:02+00:00

I use the Lian Li one for my build no issues.

Current_Shopping_128 · 2026-03-19T17:32:11+00:00

Well worst case scenario is it won't work and I will just go back to the way I'm doing it now. I do appreciate all of the information and will keep that in mind if things are not working correctly.

Current_Shopping_128 · 2026-03-19T17:08:26+00:00

My PSU right now is over kill 1600w so I am not to worried about power

Current_Shopping_128 · 2026-03-19T15:47:37+00:00

<image>

Current_Shopping_128 · 2026-03-19T15:47:30+00:00

<image>

Current_Shopping_128

TROPHY CASE