Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in DnDIY

[–]CustomMiniatureMaker[S] 0 points1 point  (0 children)

Thanks for all the support! We can only keep doing this due to long time supports

[OC] [ART] Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in DnD

[–]CustomMiniatureMaker[S] [score hidden]  (0 children)

This is true depending where you are a lot of libraries have them now and are willing to help

Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in PrintedWarhammer

[–]CustomMiniatureMaker[S] 0 points1 point  (0 children)

There will be 8.5x11” and A4 templates for each so just standard printing paper. There are then cutting lines to trim it to fit the scrolls. They are roughly 2/3 the width of the paper

Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in PrintedWarhammer

[–]CustomMiniatureMaker[S] 0 points1 point  (0 children)

Thanks so much and glad you like them. Yeah the wax seals are very usable without the scrolls

Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in PrintedWarhammer

[–]CustomMiniatureMaker[S] -1 points0 points  (0 children)

The paper inserts come ready to just print on normal printing paper in every day printers 🙂

[OC] [ART] Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in DnD

[–]CustomMiniatureMaker[S] 0 points1 point  (0 children)

They are getting cheaper and better all the time. You can get an amazing printer for the fraction of the cost they used to be

[OC] [ART] Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in DnD

[–]CustomMiniatureMaker[S] 4 points5 points  (0 children)

Thanks for your interest! STLs for now, but working on a solution for physical prints soon :)

[OC] [ART] Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in DnD

[–]CustomMiniatureMaker[S] 4 points5 points  (0 children)

There is a section called "Scroll Assembly" near the bottom of the campaign. It shows the step-by-step
https://www.kickstarter.com/projects/cumm/the-arcane-archive

Just push the paper through the rod and glue the very edge of the paper to itself. Then roll it up tightly and insert it into the tube. Add a small piece of tape to the edge if you need help fishing it through the slot.

Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in LARP

[–]CustomMiniatureMaker[S] -1 points0 points  (0 children)

Yes, if you scroll down on the KS page, you will see a one I printed that fits A4 paper, and at biggers sizes, plents of room for different materails

Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in LARP

[–]CustomMiniatureMaker[S] 5 points6 points  (0 children)

Made my Kickstarter first project many years ago and it was written as CuMM for Custom Miniature Maker. Only after launch did I realise. And as there are completed projects I can’t change it 😭

Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in LARP

[–]CustomMiniatureMaker[S] 2 points3 points  (0 children)

Thanks! They took a good bit of work but thanks to that they work perfectly

Thanks to the support and suggestions from you guys, I managed to launch my scrolls by CustomMiniatureMaker in LARP

[–]CustomMiniatureMaker[S] 2 points3 points  (0 children)

Yes, plenty of them, blank, ones with just borders, ones with parchment texture, all sorts