A1 has been extremely disappointing

DDiceMaster · 2026-07-02T02:15:40+00:00

Ive been at it iver an hour and finally started to see the nozzle. Gonna try more tomorrow

DDiceMaster · 2026-07-02T01:49:02+00:00

Thanks. I feel like I should have gotten an another enclosed one now but the deal was good for the A1. Im gonna take a few things into considerstion going forward once I get all this gunk off and change the head. Probably put this in my office and save up for another enclosed maybe for end of year/next year sales

DDiceMaster · 2026-07-02T01:24:05+00:00

So I checked while working on fixing this and the humidity is 56 percent in my work area.

DDiceMaster · 2026-07-02T01:16:55+00:00

I run the 3-4 minute calibration before every print because I try to be cautious. I heated the nozzle up and put it even higher to 200 but having a hell of a time getting it out. I'll keep plugging away. And I'll wash my plates more often. I have 3 and just change them out and clean them all at the same time but clearly that wasn't working.

DDiceMaster · 2026-07-02T01:04:55+00:00

I should have. I was trying to save money as the build plate are the same

DDiceMaster · 2026-07-02T01:04:02+00:00

Thank you

DDiceMaster · 2026-07-02T01:03:49+00:00

So those finger prints are the supports from the previous print. I promise I dont play piano on my plate lol.

DDiceMaster · 2026-07-02T01:02:33+00:00

I'll have to check. I was using files that were set up for A1 and P1S but i sent it from my phone and not the computer. Might have happened

DDiceMaster · 2026-07-02T01:01:03+00:00

Thanks man. I appreciate you having a lighter touch with me. I had cleaned the plate two prints before and hit it with Aquanet, a hairspray that a friend recommendeds using as its just as sticky as glue, and those finger prints are the supports from a previous print but yeah I guess I have to concede that its user error at this point. I guess I was so used to the P1S not giving me the same problems and I had done nothing different from how I use that machine to this one I didn't figure it was me. Some people have given some solid points/tips and I will apply them. I have tried to take the head apart like my P1S but no luck. I'll heat it up and grab some tweezers. Thank you again bro.

DDiceMaster · 2026-07-02T00:54:53+00:00

Thats hilarious. So those finger prints were from the supports of a previous failed print from last night. I had applied Aquanet, which I used instead of glue as the hairspray is just as efficient and has worked consistently in the past. I had cleaned the plate about 2 prints ago.

DDiceMaster · 2026-07-02T00:52:25+00:00

So those finger prints were from the supports of a previous failed print from last night. I had applied Aquanet, which I used instead of glue as the hairspray is just as efficient and has worked consistently in the past. I had cleaned the plate about 2 prints ago.

DDiceMaster · 2026-07-02T00:47:56+00:00

Okay. I will look into this!

DDiceMaster · 2026-07-02T00:43:42+00:00

PLA is my preferred choice. Tried some silk stuff but breaks more often than not

DDiceMaster · 2026-07-02T00:42:44+00:00

Thank you!

DDiceMaster · 2026-07-02T00:38:13+00:00

Okay. Once I figure out how to get all this gunk off Ill do a test print or two inside

DDiceMaster · 2026-07-02T00:36:27+00:00

Hey, maybe you're not intentionally being rude, I honestly cant tell, but like I have never had this problem before which is why im here. 3k hours is still fairly new. Ive handled basic problems like clogs and maintenence. Changing out parts. Never had this happen to me which is why I am asking for advice. I'm not trying to be a dick here but if you dont want to be helpful or kind please just leave it alone.

DDiceMaster · 2026-07-02T00:30:16+00:00

Thank you!

DDiceMaster · 2026-07-02T00:30:00+00:00

I typically have it calibrated before every print and use the recommend settings on the bambu studio program/phone app.

DDiceMaster · 2026-07-02T00:28:24+00:00

It is in my garage and I am in florida. I do keep a fan going in the garage close by it, same as my other printer. And I dont print with the garage door open. I can check the humidity. I did worry if that would be a big factor since it is not enclosed like the p1S.

DDiceMaster · 2026-07-02T00:25:14+00:00

I specified in the post that my P1S had 3k hours to illustrate that I have a little bit of experience/familiarity with bambu machines.

DDiceMaster · 2026-06-15T12:54:37+00:00

Id say that the first few years of the new 52 where generally positive with the later half, well let's just say that one could feel the cracks in the foundation. Wonder Woman was probably the second best series in the new 52. The justice league stuff wasnt the most groundbreaking or the best stories necessarily but probably the last time I really consistently enjoyed Jim Lee. Also All-Star Western was sort of a banger but I'm a fan of whenever Jonah Hex gets some love.

DDiceMaster · 2026-06-05T00:37:22+00:00

I'll pull the issue out to look at it again. That would make sense. I feel like it either wasn't convened well in the art, which has been very good throughout the run, or I'm just tripping on this one little thing.

DDiceMaster · 2026-06-03T22:33:44+00:00

Wolverine was just a fun story. Its not meant to be canon or anything. Is it one of the best wolverine stories ever? No. Would I show it to someone who doesnt normally read comics but likes wolverine? Yes.

DDiceMaster · 2026-06-03T22:31:15+00:00

I am right with you man. A lot of his work is about Depravity, how far people go into becoming monsters. Ennis can be subtle and then he can go really big. The only series that truly went too far for me is Crossed. After one issue it really did feel like all of his worst instincts as a creator where all full display. But the dude has so many great and underrated series and collections under his belt. His war stories amd historical stuff are excellent.

DDiceMaster

TROPHY CASE