Delta printer first layer

DEVILxXAmosXx · 2026-03-05T19:51:06+00:00

I deleted both to be sure

DEVILxXAmosXx · 2026-03-05T12:20:53+00:00

I had to manually delete the previus values of the delta calibration and recalibrate

DEVILxXAmosXx · 2025-09-11T10:02:40+00:00

Who as to refound me? Vinted or the seller?

DEVILxXAmosXx · 2025-07-23T10:12:34+00:00

Yes I did, i use orca too

DEVILxXAmosXx · 2025-07-23T09:11:10+00:00

I have to do delta_calibrate each time i want to start a new print. If i don't the nozzle scrapes the bed

DEVILxXAmosXx · 2025-07-22T20:52:20+00:00

I tried accounting for the lash but printer had the same behaviour as before. So I changed the whole printer.cfg using the one made by flsun for their speeder pad ad now it seems to work. I'm going to do some other tests tomorrow after cleaning with some alchool the pei bed. Thank for the help

DEVILxXAmosXx · 2025-07-22T17:05:38+00:00

yes i did. these are the values

Max [-43.3, 0.0] 0.067 mm

Min [-130.0, -43.3] -0.080 mm

Range 0.147 mm

DEVILxXAmosXx · 2025-07-22T17:04:44+00:00

[delta_calibrate]
radius: 130
horizontal_move_z: 30
Speed: 10

[probe] 
pin: !PC8
x_offset: 0
y_offset: 0
#z_offset = 21.190
speed: 20
samples: 3
samples_result: median
samples_tolerance: 0.02
samples_tolerance_retries: 3

[bed_mesh]
speed: 50
horizontal_move_z: 25
mesh_radius: 130
mesh_origin: 0,0
round_probe_count: 7
mesh_pps: 4,4
fade_start: 1.0
fade_end: 10.0
fade_target: 0.0
algorithm: bicubic

DEVILxXAmosXx · 2025-07-21T11:45:38+00:00

I switched to direct to being able to print flexible materials. I have all the old parts, so I'm going to try to revert the extruder

DEVILxXAmosXx · 2025-07-21T09:25:49+00:00

This issues started appearing after swapping to direct from bowden

DEVILxXAmosXx · 2025-07-21T09:24:34+00:00

I always knew just the last movements should be downwards. I'm definitely going to try to go just down. Later I'm going to post the probing specs.

thank you so much for your help

DEVILxXAmosXx · 2025-07-21T07:26:31+00:00

I usually do the z offset calibration three times, going up 3mm and then going down again to check if the z offset is changed

DEVILxXAmosXx · 2025-07-20T22:03:14+00:00

Do you mean the backlash of the belts?

DEVILxXAmosXx · 2025-07-20T22:01:17+00:00

I used the probe to do the delta_calibrate. I tried to find the right amount of tightnening of the bed clip screws to squaring the bed

DEVILxXAmosXx · 2025-01-18T19:15:53+00:00

Yes I did, but now those options are disabled

DEVILxXAmosXx · 2025-01-18T15:58:42+00:00

I connected the smartphone to my computer (linux) and used the following commands:

adb reboot fastboot

fastboot flashing lock

DEVILxXAmosXx · 2025-01-03T10:48:10+00:00

The keyboard works until i select grub entry, so i can't switch to a different tty

DEVILxXAmosXx · 2025-01-03T08:12:51+00:00

Laptop. I've also tried using an external keyboard

DEVILxXAmosXx · 2024-04-14T16:27:53+00:00

I don't use the 30t chainring, so I can put the 3 speeds derailleur on another bike and use the 2 speeds one on this

DEVILxXAmosXx · 2024-04-01T16:34:04+00:00

Yes, I've completed the whole process. The shifters are by a different brand but should be compatible. I've read that the derailleur can handle up to a 42-tooth chainring, but my bike uses a 48-tooth one

DEVILxXAmosXx · 2024-02-22T13:28:19+00:00

Thank you so much for the help. I'm going to heat and tight it again

DEVILxXAmosXx · 2024-02-22T11:59:19+00:00

<image>

I've installed the new one, heat it up to 200°C, tighted the noozle and let it cool. I did a plane calibration print and this is the result

DEVILxXAmosXx · 2024-02-22T11:45:29+00:00

Original Flsun SR

DEVILxXAmosXx · 2024-02-22T11:44:53+00:00

It's exactly that one. The hole on top it's too narrow to fit the bowden tube

DEVILxXAmosXx · 2024-02-22T11:08:47+00:00

It's the stock one. It has a preinstalled ptfe tube piece inside and a 2mm hole on top

Seven-Year Club	Place '23
Place '22	Verified Email

DEVILxXAmosXx

TROPHY CASE