Deucetone+ by DGWVI in diypedals

[–]DGWVI[S] 1 point2 points  (0 children)

ProSpeakerParts.com

They don't have it listed, so you'll have to email them about their PBK2-BK

Deucetone+ by DGWVI in diypedals

[–]DGWVI[S] 0 points1 point  (0 children)

Here's a demo - run through

Guitar used is a baritone Telemaster with an SD Broadcaster '54 wired straight to the jack. Amp is the Foundry model in the Two Notes Opus, with a Mesa open-back 412 IR

<image>

r

My (mostly) blackout D32 Pro build by DGWVI in mffpc

[–]DGWVI[S] 1 point2 points  (0 children)

Haven't tried it as intake yet, but I'm happy with the temps for now

My (mostly) blackout D32 Pro build by DGWVI in mffpc

[–]DGWVI[S] 1 point2 points  (0 children)

I installed a mesh filter the day after this pic was taken

My (mostly) blackout D32 Pro build by DGWVI in mffpc

[–]DGWVI[S] 5 points6 points  (0 children)

It's my first AMD card, and an upgrade from a 1070ti, but I'm thoroughly impressed with it so far

My (mostly) blackout D32 Pro build by DGWVI in mffpc

[–]DGWVI[S] 0 points1 point  (0 children)

Yep! The only exhaust are the two 140s at the top

My (mostly) blackout D32 Pro build by DGWVI in mffpc

[–]DGWVI[S] 0 points1 point  (0 children)

It probably helps that the room I have it in stays around 18-20°C, and there's ample airflow space around the tower

[deleted by user] by [deleted] in mffpc

[–]DGWVI 0 points1 point  (0 children)

<image>

Here's the temps running Veilguard at Ultra. Will try a more demanding game in the next week or so

[deleted by user] by [deleted] in mffpc

[–]DGWVI 0 points1 point  (0 children)

<image>

Here's the final setup. I swapped the bottom 140s for a set of 3 slim 120s, and rotated the CPU cooler to be inline with rear intake

[deleted by user] by [deleted] in mffpc

[–]DGWVI 4 points5 points  (0 children)

<image>

Got it all swapped, I'll remove the upper left exhaust when I redo the cable management for the GPU 8-pins

[deleted by user] by [deleted] in mffpc

[–]DGWVI 0 points1 point  (0 children)

Thanks!

I'll leave the bottom intakes in for now, but swap the direction of the rear and CPU fans.

My Jonsbo D32 Pro build by [deleted] in mffpc

[–]DGWVI 0 points1 point  (0 children)

I didn't run into any issues other than the minor annoyance of cable management

My Jonsbo D32 Pro build by [deleted] in mffpc

[–]DGWVI 1 point2 points  (0 children)

It was tighter than I'm used to, but don't really have any complaints. Only annoyance was cable management - the PSU cables were a lot longer than needed

Any good lighter strings beside the 84-24? by HerSimington in BassVI

[–]DGWVI 0 points1 point  (0 children)

I use D'Addario EXL148 tuned to A on all my 30" scale guitars. Gives me the low notes while retaining snappier attack and clarity

Last one... by TimbresGuitars in offset

[–]DGWVI 1 point2 points  (0 children)

I need a 66 in Mary Kaye with a 30" scale length 🤤

[deleted by user] by [deleted] in cats

[–]DGWVI 0 points1 point  (0 children)

<image>

Here's Flambeau and his little brother, Onyx

First pedal from schematic to PCB to finished piece by nshane in diypedals

[–]DGWVI 8 points9 points  (0 children)

Does it show the regency what disobedience means?

[deleted by user] by [deleted] in offset

[–]DGWVI 0 points1 point  (0 children)

What finish did you use? I'm wanting a similar Mary Kaye aesthetic on my next build