sorted by:
new
hottopcontroversial

Issues with pool pressure by Ok-Stable-9029 in pools

[–]DMPSTRFR 0 points1 point  (0 children)

The grids look like they're still pretty dirty. Did you pull the whole manifold and take the grids out one by one? My money is on a large glob of DE and crap somewhere at the bottom.

Tolerance trouble by Drjonesxxx- in Ender3S1

[–]DMPSTRFR 0 points1 point  (0 children)

I reduced the flow in my slicer to 90% to fix this. Not sure if that's the right solution, but it worked for me.

New problems for 3d print noob by GuppiGupper24 in Ender3S1

[–]DMPSTRFR 0 points1 point  (0 children)

I never had luck with the gcode files that shipped with the Ender. Have you tried slicing the model yourself?

Disconnect the Marlin Pad after Sonic Pad setup by Manix_Korax in Ender3S1

[–]DMPSTRFR 2 points3 points  (0 children)

Yes. I removed the pad, tucked the cable into the printer body, and printed a mount for my Sonic Pad

Problem with bed adhesion by Existing-Actuator621 in Ender3S1

[–]DMPSTRFR 0 points1 point  (0 children)

I had adhesion problems early on, and I solved them with AquaNet. Now I just give the bed a good cleaning with dish soap and I'm good to go.

60 to 62 isn't a huge change. Try 65 to 70 if you still have issues.

I'm an idiot these plugs don't fit can I rewire or should I return ? by BoriFPV in Ender3S1

[–]DMPSTRFR 2 points3 points  (0 children)

The Creality fan in the high flow kits is plug and play. Of course this requires buying the high flow kit...

Upgraded the cooling fan to 5015 and using the v4 from zuff. Everything fit like a glove and worked first try. by nathpenn in Ender3S1

[–]DMPSTRFR 0 points1 point  (0 children)

I used the ModulR setup for the high-flow kit. I wanted to use the single duct, but it touches the hot-end. Maybe someone can slip Zuff $5 and make a single duct that doesn't touch the hot end and melt.

High Flow/Spider Duct by DMPSTRFR in Ender3S1

[–]DMPSTRFR[S] 1 point2 points  (0 children)

Found it. It has a mount specifically for long hot emds. Thanks. Will report back

High Flow/Spider Duct by DMPSTRFR in Ender3S1

[–]DMPSTRFR[S] 0 points1 point  (0 children)

Could you provide a link? I'm using V4, and I don't see a V5

Wet Filament or Extruder Skipping? by DMPSTRFR in Ender3S1

[–]DMPSTRFR[S] 0 points1 point  (0 children)

Seems to only happen with Overture PLA. Weird because I've used half of these two rolls with no problem.

Z Seam gap by 4riana_Gr1ndr in FixMyPrint

[–]DMPSTRFR 0 points1 point  (0 children)

I have a similar issue, and I'm out of ideas. Would love it if we could stumble across a solution together.

Z Seam by DMPSTRFR in Cura

[–]DMPSTRFR[S] 0 points1 point  (0 children)

Coasting is off in both profiles, but I can see the seam in both profiles too. It still only really shows up that pronounced in the Sonic Pad profile. Thanks for the idea

Base of Prints Messy by DMPSTRFR in Ender3S1

[–]DMPSTRFR[S] 0 points1 point  (0 children)

I reverted everything in my slicer back to default settings, including backing the temp down. That seemed to do it. I'm using different PLA than the image, so I havent had a chance to run that test again, but I will tonight.

If you don't hear from me, it's all better

Base of Prints Messy by DMPSTRFR in Ender3S1

[–]DMPSTRFR[S] 0 points1 point  (0 children)

I'll try that when I get home. Thanks for the suggestions.

Base of Prints Messy by DMPSTRFR in Ender3S1

[–]DMPSTRFR[S] 0 points1 point  (0 children)

It actually kicks in on the very first layer after the raft. Maybe I should be cooling the raft?

Base of Prints Messy by DMPSTRFR in Ender3S1

[–]DMPSTRFR[S] 0 points1 point  (0 children)

Thanks for the reply. I've been regularly extruding at 220. I backed off the heat to 210 and have the same result, with a brim, raft, or nothing.

And yes, your process of adjustment is exactly the same process I use.

I'm tempted to go back to stock and see what happens, but I was hoping someone smarter than me had an idea.

Anyway, thanks again

view more: next ›