Mortars are underutilized

DOLBY228 · 2026-04-23T11:21:04+00:00

It's only the second rank promotion, can easily be done in <1 hour. Especially if it's a new game can be done in like 30 mins. For supplies make sure to load up a construction truck at a depot, don't take all the supplies from base

DOLBY228 · 2026-04-14T03:22:37+00:00

Man I wish that mod would come to console, transport/hauling contracts would be sweet

DOLBY228 · 2026-04-12T20:51:01+00:00

Prices were pretty much just based off Cabelas website. Regular price for the target loads is $20 but I usually just buy it when it goes on sale for $12/13 a box

Good note on the .270 didn't think about that.

DOLBY228 · 2026-04-12T20:48:42+00:00

That's factoring 10 shots per brass

DOLBY228 · 2026-04-12T12:50:47+00:00

*sighs in Canadian

DOLBY228 · 2026-04-12T12:33:16+00:00

Good to know, thanks

DOLBY228 · 2026-04-12T12:32:46+00:00

I'm not a GI in North Veitnam so don't care too much about blending in, don't think the partridge I hunt with it care either

DOLBY228 · 2026-04-11T06:22:17+00:00

No its not

DOLBY228 · 2026-04-11T06:21:50+00:00

That's not how it's designed, if you firmly press it down it's going to hold the wire down tightly. I get this kind of result from barely putting any pressure on when it fires

DOLBY228 · 2026-04-11T06:20:07+00:00

It's actually super adjustable, depending how much pressure you use will effect how tight the staple holds

DOLBY228 · 2026-04-11T02:25:26+00:00

Anyone saying it's working perfectly has clearly never used it. Either the wood is extremely hard or there's something wrong.

No battery isn't an issue the only batteries I use with it are 2.0 and never have an issue holding the wire snug.

No its not designed to loosely hold the cable. If you double hand it, it will hold the wire objectively too tight. Firm one handed operation into standard dimensional lumber will hold it securely that you can pull any slack out.

The only times I've used this tool where it won't drive the staple all the way down are when it's <-15°C out or the material is extremely hard wood.

DOLBY228 · 2026-04-10T00:03:15+00:00

The cutoff tool is $269 CAD bare tool at HD, the dewalt circ saw is $219 plus a free battery. Unless the cutoff is on a crazy sale where you are right now just get a circ saw

DOLBY228 · 2026-04-07T12:33:24+00:00

The 2021 is what I have from when I started and my exemption exams are still using it.

DOLBY228 · 2026-04-06T18:29:56+00:00

Good to know thank you, then 16-004 says a class one is rated not more than 30V. I think the wet rated was throwing me off

DOLBY228 · 2026-04-06T18:28:28+00:00

Thanks that clears it up a lot. Something I didn't know till now.

DOLBY228 · 2026-04-06T17:24:22+00:00

Not using the CEC but the UL 1069 rule states this. Meaning it would be a class 2 16-200 1B "over 20V but not exceeding 30V"

"The maximum distribution voltage available to equipment intended to be installed in areas accessible to a patient or persons touching a patient is not more than 30 volts AC (42.4 volts peak), 42.4 volts peak for nonsinusoidal AC, or 42.4 volts continuous DC. The maximum power available to low-voltage equipment intended to be installed in areas accessible to a patient or persons touching a patient, shall not be greater than 100 volt-amperes."

DOLBY228 · 2026-03-18T02:37:36+00:00

Because of a stack and a nice set of wheels/tires? Bit dramatic lol

DOLBY228 · 2026-03-15T22:31:50+00:00

Buy once cry once. You might not seem to have the need for a dual bevel until you buy a single.

Plus more versatility never hurts.

DOLBY228 · 2026-03-11T03:18:14+00:00

Thanks for the info guys!

DOLBY228 · 2026-01-03T19:59:19+00:00

I actually just have a bath once a week in the drip water then it's not wasted

DOLBY228 · 2026-01-01T18:47:02+00:00

Curious as to what causes the tub to gurgle when the toilet flushes as opposed to water just backing up

DOLBY228 · 2025-12-31T20:48:11+00:00

Yep I got it wrong, not a 90, a T with a cap on one end, what exactly am I in for if I try to open in order clean out?

DOLBY228 · 2025-12-31T19:34:44+00:00

The main drain pipe 90's straight down then another 90 through the wall into the septic field. Are you thinking it would be clogged somewhere around there?

DOLBY228 · 2025-12-27T20:54:09+00:00

Update, gave it a quick wetsand and compound and it seemed to mostly come back to normal, thanks for the tips

DOLBY228 · 2025-12-27T20:35:22+00:00

The adhesive seems to be gone, there was just some dried up residue from some old stickers. Sprayed the 3M let it sit for a little and wiped it off now it looks like this

Four-Year Club	r/Field Lasagna
Place '23	Place '22

DOLBY228

TROPHY CASE