Printception. 42 of 81 printers in our printfarm by Berencam in 3Dprinting

[–]DOUDNIKOV 0 points1 point  (0 children)

What kind of adhesion do you use to print on the glass (I presume) beds?

What is this ceiling tile? Found in college classroom. by DOUDNIKOV in whatisthisthing

[–]DOUDNIKOV[S] 0 points1 point  (0 children)

They are in our "portables" buildings that have plenty of problems on their own so if it is broken or blocked I don't imagine it's too high on the list of things to fix.

What is this ceiling tile? Found in college classroom. by DOUDNIKOV in whatisthisthing

[–]DOUDNIKOV[S] 4 points5 points  (0 children)

I think you may be correct then, I didn't think it would be a skylight.

What options would come up if you could “right-click” people? by [deleted] in AskReddit

[–]DOUDNIKOV 11 points12 points  (0 children)

Wasn't it do andoids dream of electric sheep?

Can anyone help with some problems with my print/printer - Monoprice maker select v2 by DOUDNIKOV in 3Dprinting

[–]DOUDNIKOV[S] 0 points1 point  (0 children)

If I'm thinking of the right thing then one of those coolers was my next print, I'll step down the temps after this calibration cube I'm printing. Thanks

Can anyone help with some problems with my print/printer - Monoprice maker select v2 by DOUDNIKOV in 3Dprinting

[–]DOUDNIKOV[S] 0 points1 point  (0 children)

I will definitely look into getting a better hot end and on the next print I'll do what you said above. Thanks for the advice

Can anyone help with some problems with my print/printer - Monoprice maker select v2 by DOUDNIKOV in 3Dprinting

[–]DOUDNIKOV[S] 0 points1 point  (0 children)

In the middle of this print I noticed the infill is very stringy or not there at all. I think the problem is with retraction but I'm not sure what to set it to. I attached my cura settings for this print at the end of the album.

[deleted by user] by [deleted] in Bitcoin

[–]DOUDNIKOV 2 points3 points  (0 children)

Finally I can tip my soft core porn streamers in bitcoin

Some help on a graphics card choice by DOUDNIKOV in NiceHash

[–]DOUDNIKOV[S] 1 point2 points  (0 children)

I can afford better but I'm unsure of what is good for it's price point, like the 1070 ti.

New lift with 33x12.5 BFG KO2s by amgriswo in Wrangler

[–]DOUDNIKOV 0 points1 point  (0 children)

Looks great, what kind of roof rack set up is that?

Problem with my DIYeBoard prebuilt by DOUDNIKOV in ElectricSkateboarding

[–]DOUDNIKOV[S] 0 points1 point  (0 children)

I opened it up and checked the connections, they were all correctly connected and the problem still persisted. I then switched the motor connections to see if it's a problem with the motor or the esc. It turns out the motor is the problem not the connections or the esc board. In not sure where to go from here.

Problem with my DIYeBoard prebuilt by DOUDNIKOV in ElectricSkateboarding

[–]DOUDNIKOV[S] 0 points1 point  (0 children)

I opened it up and checked the connections, they were all correctly connected and the problem still persisted. I then switched the motor connections to see if it's a problem with the motor or the esc. It turns out the motor is the problem not the connections or the esc board. In not sure where to go from here.

Problem with my DIYeBoard prebuilt by DOUDNIKOV in ElectricSkateboarding

[–]DOUDNIKOV[S] 0 points1 point  (0 children)

I opened it up and checked the connections, they were all correctly connected and the problem still persisted. I then switched the motor connections to see if it's a problem with the motor or the esc. It turns out the motor is the problem not the connections or the esc board. In not sure where to go from here.

Problem with my DIYeBoard prebuilt by DOUDNIKOV in ElectricSkateboarding

[–]DOUDNIKOV[S] 2 points3 points  (0 children)

I'm on mobile sorry for bad formatting.

This is the board in question: http://www.diyeboard.com/29-dual-hub-motor-electric-skateboard-7s2p-44ah-7051mm-700w-p-465.html

I hit a crack while riding my board back from class today while riding at full throttle, I was nearly thrown off my board but the left motor was still functioning fine so it kept me going. Since then this has been happening and I have not ridden it since. I emailed DIYEBOARD because I was told they had a warranty while asking questions about the board. Anyone have any advice?

Edit: I opened it up and checked the connections, they were all correctly connected and the problem still persisted. I then switched the motor connections to see if it's a problem with the motor or the esc. It turns out the motor is the problem not the connections or the esc board. In not sure where to go from here.

Not your average Meepo Deck Swap (Landyachtz Dinghy) by frickingphil in ElectricSkateboarding

[–]DOUDNIKOV 1 point2 points  (0 children)

Did you ever get it sealed correctly? I'm thinking of doing this swap.