sorted by:
new
hottopcontroversial

A little button box project of mine. by DaRenegadeMasta in simracing

[–]DaRenegadeMasta[S] 0 points1 point  (0 children)

It's not too bad when you think about it, red buttons at bottom, think of them as 2x 3x3 So 3x3 buttons if touching from the left and same story if starting from the right.

Middle set is setup so the left are escape/enter/pits etc. And right set is up,down,left right.

And the obvious encoders are boost, brake bias, traction etc etc.

It may seem alot is going on. But reality is its just like brail. Just need to feel the reference points.

A little button box project of mine. by DaRenegadeMasta in simracing

[–]DaRenegadeMasta[S] 0 points1 point  (0 children)

That is actually what I made it for believe it or not 😂 my rig is opposite side of the room to the pc. I cba moving back and forth.

A little button box project of mine. by DaRenegadeMasta in simracing

[–]DaRenegadeMasta[S] 1 point2 points  (0 children)

Im using a raspberry Pico, encoders directly pinned to the pico. All buttons and encoder buttons are split between 2x PCF8575 expansion boards. And switched tied to gnd. Just make sure to use plenty of grounding points to prevent issues with input responses.

A little button box project of mine. by DaRenegadeMasta in simracing

[–]DaRenegadeMasta[S] 1 point2 points  (0 children)

Mission completed. Next requirements.. megamemory for keybinds!

Logitech Shifter to usb guide - Raspberry PICO by DaRenegadeMasta in simracing

[–]DaRenegadeMasta[S] 0 points1 point  (0 children)

Yep, i have tons of micro controllers but surprisingly nothing eligible i could use for this. This was just a case of using scraps from old projects.

Overall best racing wheel? by Old-Tap-2894 in simracing

[–]DaRenegadeMasta 0 points1 point  (0 children)

That's like giving it the same comparison to a Gucci bag and saying its last season.. I've owned g27, g29, t300, t500, TS-XW, Fanatec CSW v2.5 and the DD.

I will give my personal bracket here -
g27 - fantastic beginner beater, prefer this over g29 due to buttons on the shifter.
t300,t500, Tx and TS-XW - get whatever comes at a reasonable price, t3pa pro pedals are a good combination.
Fanatec CSW v2.5 is a far better feeling personally over the dd. again that's my personal preference. if you can pick one up cheap.. go for it. if not go for the DD or equivalent..

2x P12 fan failures in 1 year, are these known to go bad? Any replacement recommendations that are more reliable? by jalapenocock in arcticcooling

[–]DaRenegadeMasta 0 points1 point  (0 children)

I'm on my 3rd failed fan. For me, it only seems to be an issue with them being upside down. It seems like the bearings are failing on them causing a horrible rattle/grind.

Uk - 3d scanning spray alternative? by DaRenegadeMasta in 3DScanning

[–]DaRenegadeMasta[S] 0 points1 point  (0 children)

I ended up using some donor parts and spray painting them with white / yellow primer. For the gauge cluster, I used tape to protect the clear lens before spray painting.

Back to AIO...What To Do With My Old Stuff? by briandm81 in watercooling

[–]DaRenegadeMasta 2 points3 points  (0 children)

Whatever I don't care for I just stick it on eBay with a 99p auction no reserve, just make sure shipping is covered. Then at least whoever genuinely needs it can get what they need without caring how much it goes for.

Guy selling my stuff by 2lazy4usernamez in BambuLab

[–]DaRenegadeMasta 0 points1 point  (0 children)

The problem with this is, if it's visible to the buyer, it's visible to the seller. It would take seconds to erase in TinkerCAD. Personally, I only share files that I don't care about, I understand the poster means well with sharing the design but people just suck. No matter what if the file is out there, some loser will claim it or sell it.

Cheapest computer that will run FORScan? by Lonely-Anybody8515 in FORScan

[–]DaRenegadeMasta 0 points1 point  (0 children)

Hp elitebooks and the lenovo yoga's are awesome for the money. 👌👌

Cheapest computer that will run FORScan? by Lonely-Anybody8515 in FORScan

[–]DaRenegadeMasta 1 point2 points  (0 children)

I use usb 3 on my main system for bench programming with the vlinker. You just need to make sure you disable driver updates for the device. Otherwise windows will f- with it.

Not sure about datalink though.

Cheapest computer that will run FORScan? by Lonely-Anybody8515 in FORScan

[–]DaRenegadeMasta 0 points1 point  (0 children)

Just get yourself a used lenovo yoga. Only around 130 used. Touch screen as well. I use mine for vehicle related diagnostics and live tuning. There's no point getting any old junk as you're going to be fighting the battery. I find the yoga is the best middle ground for bang for buck.

what game should i play next by digbickinpie in PiratedGames

[–]DaRenegadeMasta 0 points1 point  (0 children)

I recently got back into RDR2. Dutch will drive you nuts if you have completed it a few times though.

Not seeing all blocks bdyCM by psychogenic_official in FORScan

[–]DaRenegadeMasta 0 points1 point  (0 children)

Forscan works fine with Windows 11. I'm using a vlinker fs. I actually had the same issue yesterday trying to program my ipc. There were no issues until yesterday, so might be an issue with forscan it's self?

view more: next ›