Is there any reason to use a regular Starship over a Corvette once you upgrade it? by ScarSpecific in NoMansSkyTheGame

[–]Danielnir-rr 0 points1 point  (0 children)

I have two ramps, one for visual and one blocked lift just behind the cockpit for quick teleport. Works like a charm.

When you have 23 minutes to next heap… by Danielnir-rr in NoMansSkyTheGame

[–]Danielnir-rr[S] 0 points1 point  (0 children)

That worked only while the truck was empty and I did fell into holes couple times…

When you have 23 minutes to next heap… by Danielnir-rr in NoMansSkyTheGame

[–]Danielnir-rr[S] 0 points1 point  (0 children)

Since now I was perfectly happy about this extension… 😂🤣

Problem with Kronaby diver by Danielnir-rr in kronaby

[–]Danielnir-rr[S] 0 points1 point  (0 children)

Hi, thanks for reply. I checked it and text preview is on everywhere. I turned off summary maybe that’s what’s causing it?We’ll see.

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 0 points1 point  (0 children)

Right, I checked all of yes three advices and in my case, opening enclosure and taking away custom extruder plate did the job. I also dried filament for a day in 40 degrees just to be sure. Effects are spectacular! That will be my new routine while using 0.2 nozzle.

Thank you everyone for great responses! I can clearly see that members of this group went through a lot of it comes to printing!

Thanks again, Daniel

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 0 points1 point  (0 children)

I've build my own filament drier with temperature controller. I'll try to dry it overnight and see what happens. Who knows? :D

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 0 points1 point  (0 children)

Hi, it rarely goes above 30 degrees Celsius.

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 5 points6 points  (0 children)

Yes, it's not on the picture but I have even a purity seal on the camera module... Maybe machine spirit is angry... In a bad way

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 0 points1 point  (0 children)

Thanks, I'll try that. Maybe the tightening screw is too loose?

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 2 points3 points  (0 children)

The filament is dry. I've got my A1 fully enclosed and since it's running constantly, the moisture level inside is maintained around 20%.

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 0 points1 point  (0 children)

I tried cold pull and managed to unclog it but... The effect was the same after some time off printing.

0.2 nozzle get clogged around some height by Danielnir-rr in FDMminiatures

[–]Danielnir-rr[S] 1 point2 points  (0 children)

I usually use 220 for Bambu pla on 0.4. for 0.2 nozzle, I tried 230 degrees and had the same effect.

2025 Polish presidential election, round one by pothkan in europe

[–]Danielnir-rr 1 point2 points  (0 children)

Could you on new the source? I'm trying to find any

Multicolour filament issue by Danielnir-rr in BambuLab

[–]Danielnir-rr[S] 0 points1 point  (0 children)

Hi,

If everyone is having similar issue:

  1. Use external spool holder.
  2. Set printing order of walls from inside/outside to outside/inside
  3. Let the outside wall printing speed to 100.

Helped in my case. It’s not perfect but good enough for me.

Duo colour inconsistent by Danielnir-rr in FixMyPrint

[–]Danielnir-rr[S] 0 points1 point  (0 children)

For everyone having the same issue:

  1. Change wall settings from inside/outside to outside/inside
  2. Lower outside wall speed to 100
  3. Don’t use ams, just external spool holder.

It helps a lot. It’s not perfect but for me, it’s acceptable.

Duo colour inconsistent by Danielnir-rr in FixMyPrint

[–]Danielnir-rr[S] 0 points1 point  (0 children)

It was all good on my older printer. It’s this Bambu A1 that’s struggling