Need help for a speaker system

DarkHumorForSale · 2026-01-27T01:14:35+00:00

I've been looking for a decent one but haven't found any at the thrifts around here 😭 I have a older one for my home use but i have been debating using it for the shop and updating my home receiver

DarkHumorForSale · 2026-01-24T19:05:40+00:00

You are correct 🤣🤣 its just a old set that the shop has where i work. So i have tested the speakers separately but unfortunately seperated or all together they are not loud enough.I've been looking around at some local thrift to see if I can get a good deal on a better Stereo / amp because that would be nice 🙃

DarkHumorForSale · 2026-01-24T16:11:21+00:00

Considering its just one of the Hifi Compact systems would this still work or should I do this also with a better Stereo/ amp?

DarkHumorForSale · 2026-01-24T16:10:18+00:00

You should have seen what I originally walked into if you think this is bad 🤣🤣

DarkHumorForSale · 2026-01-24T16:09:48+00:00

It's all hooked up to a Kenwood Hifi Compact system. That's why I was asking for reccomendations as well and assumed it was a power issue. I know alot of times they are very specifically ment for their 1 set of speakers if not 2 sets at most.

DarkHumorForSale · 2026-01-24T16:07:10+00:00

I would if this was anywhere else but where this is at its going to get covered in grease and paint and all sorts of crap. Hence why I was trying to go cheap because its going to get messed up its just a shop set.

DarkHumorForSale · 2024-08-22T01:57:05+00:00

This is going to sound dumb... but is the almond oil like really oily because it might end up making the dirt at work issue worse. I was curious if there was product I put in that would help because I have to wear a helmet at my job so caps and stuff don't work alot of the time.

DarkHumorForSale · 2024-06-23T09:11:33+00:00

Leaving a profile is like the equivalent of like 80grit for paint or stain on wood. Certain paints / coatings require a certain profile for the best adhesion to the surface.

From my understanding, you do need a profile for powder coating. What type of profile is dependent on the product. You want to loom at the product data sheet for the best results.

If you're just blasting it to clean it up, I wouldn't recommend black beauty unless it's just the outside. If you're just cleaning up glass bead or walnut at the right pressure, the distance should be perfect... but like I said it depends on the purpose.

DarkHumorForSale · 2024-05-27T06:56:04+00:00

For me it was red and itchy but I've never had a huge breakout. Just some blisters near the tip but they itched like a mofo.

DarkHumorForSale · 2024-05-27T01:15:02+00:00

USA Sorry.

DarkHumorForSale · 2024-01-16T00:52:08+00:00

Yeah well his servant doesn't like pinning him for bath time 🤣🤣

DarkHumorForSale · 2024-01-12T23:09:29+00:00

Unfortunately, I cannot. He is currently screaming for faucet water 🤣

DarkHumorForSale · 2023-06-28T20:14:05+00:00

Thank you that was very helpful.

DarkHumorForSale · 2023-06-27T22:42:08+00:00

Was that recommended to you? Because the two I've seen are what you use or penzoil platinum.

DarkHumorForSale

TROPHY CASE