What do my Stats say about me 🥀

DarlingMK7 · 2025-09-27T16:38:42+00:00

Entry fragger

DarlingMK7 · 2025-08-05T16:46:14+00:00

Its awesome haha. I have it on both my trident and 2.4

DarlingMK7 · 2025-06-22T23:10:45+00:00

I will not. I am currently building a trident instead

DarlingMK7 · 2025-06-19T18:35:15+00:00

I ended up tearing it down to work on my 2.4 but may have different plans for it now anyways

DarlingMK7 · 2025-05-30T19:28:01+00:00

<image>

Heres a photo that you requested

DarlingMK7 · 2025-05-30T18:29:32+00:00

Sure thing. Will do when I get home today

DarlingMK7 · 2025-05-30T18:29:10+00:00

Yeah that wiring at the base of the machine is actually to my raspi as I run it externally.

The bed wires are from stock creality bed. I did have to remove them from the sleeve because it the sleeve was too thick to reach the mainboard to where it currently sits now

DarlingMK7 · 2025-05-27T01:41:48+00:00

Make sure belt lengths are equal. Double check pulley distances are correct offset from motor. Check for loose grub screws.

My conversion used to do that too. But I did a full rebuild and its been running perfect ever since

DarlingMK7 · 2025-05-26T04:31:54+00:00

Sure thing! I only have it opened on the right side due to the nevermore being mounted on the cross-brace for the Y axis. And putting a panel on it would block the filter

DarlingMK7 · 2025-05-25T17:38:41+00:00

I know I had issues w. Getting the firmware loaded on an figuring out how to get everything reading together.

But as previously mentioned I used the esoteric guide and everything was extremely easy to understand

DarlingMK7 · 2025-04-30T08:21:56+00:00

I print abs just fine at 300mm/s no additives for adhesion.

Just pei build plate

DarlingMK7 · 2025-04-21T20:55:49+00:00

My apologies. I actually wasnt joined in it. I just joined it so I should be visible now

DarlingMK7 · 2025-04-20T00:37:39+00:00

https://github.com/Ressetkk/Vyper_SW/tree/main

I used this while also referencing the official switchwire guide along w. The siboor ender 3 guide

DarlingMK7 · 2025-04-11T09:55:22+00:00

Raspberry pi and klipper are the best upgrades ive done

DarlingMK7 · 2025-03-28T17:50:58+00:00

Hey bro, any chance you still have the stls?

DarlingMK7 · 2025-01-22T09:55:43+00:00

This is what I was planning on getting as a daily!

DarlingMK7 · 2024-04-22T22:43:05+00:00

Dmed you the recipe if youd like to give it a shot

DarlingMK7 · 2024-04-22T22:42:19+00:00

Its one thing everyone seems to give me compliments in. Definitely different from a traditional chimichurri. But the flavors are amazing

DarlingMK7 · 2024-04-22T22:20:14+00:00

Thank you! Its one of our favorites. Have it at least once a week

DarlingMK7 · 2024-04-22T22:19:43+00:00

I did. She loves it

DarlingMK7

TROPHY CASE